Questions tagged [software-defined-radio]

Radio devices that use digital signal processing in place of analog electronic components to manipulate RF signals.

23 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
0answers
139 views

HackRF One and IoT overloaded?

I'm transmitting Z-Wave frames using HackRF One in loop, one frame every second. Has anyone clue why are some frames not transmitted? You can see several too long gaps between frames on Waterfall (...
3
votes
0answers
979 views

OFDM spectrum, HACKRF, and GNUradio companion

I am trying to analyze the spectrum of wifi spectrum. I getting a good OFDM spectrum with my HackRF at 2.412 GHz (from my first QTGUI Sink). But I get nothing out of OFDM Receiver. I was wondering ...
2
votes
0answers
333 views

Receiving and decoding RDS in GnuRadio

I'm new in radio, so I started with seemingly easy task - receive and decode RDS data. I use GnuRadio to understand the concept of working with RF signals. So according to standard RDS receiver looks ...
2
votes
0answers
89 views

Demodulating ISO14443 (part of NFC) using SDR?

I'm looking for info on demodulating both sides of an ISO14443 communication using a cheap SDR, preferably an RTL-SDR (R820T2+RTL2832U). The application is passively monitoring an NFC exchange for ...
2
votes
0answers
183 views

How FEC works on GNU Radio

I am new to GNU Radio. I need some reference to how to use FEC block in GNURadio. When I try to make encoder and decoder without modulation, its work as well, but when I using modulation and add ...
2
votes
0answers
426 views

How to decode 2FSK signal with SDR?

I'm new to radio and SDR but, as a hobby project, I'm trying to decode a 2FSK radio signal received by an RTL-SDR that I sent using an SI4463 transmitter. The record file contains 3 packets, but I'm ...
2
votes
0answers
480 views

LimeSDR Mini + Raspberry Pi 3 B+ Transmission problem

I am new at this. I would like to transmit an audio signal cleanly using WBFM but I see two signal peaks occur around my fundamental frequency when I start transmitting. In this case I am using a ...
1
vote
1answer
220 views

Implementing a BPSK and 4-FSK transmitters in GnuRadio (GRC) with USRP?

Currently trying to transmit a BPSK and a 4-FSK(MFSK) signal via GRC using USRP, I have two attempts at it but don't seem to be going anywhere. Still fairly new to GRC. For the BPSK, how will this ...
1
vote
1answer
83 views

How can I know (check or detect or analyze) which modulation using of my remote control switch?

Please forgive me, my native language is not English. I'm new to radio, but I have several years of programming experience. I have a raspberry pi 4 model B (...
1
vote
0answers
33 views

Sending custom EWS over DAB+ with a HackRF One

Disclaimer: I'm aware of legal issues regarding EWS! Rest assured that there is no need for concern as this is a small-scale, proof of concept done in a controlled enviroment! Greetings! I'm trying to ...
1
vote
0answers
89 views

Capture Uplink GSM packets using 820T2 and SDR

I am an extreme beginner with SDR. I am trying to use the 820T2 & SDR device to capture uplink gsm packets sent by my phone to the nearest Base Station. I have an Rx Monitor App installed on my ...
1
vote
0answers
40 views

2GFSK digital filter bandwidth calculation

I'm working on a S2LP from ST and I am configuring the RX digital filter. I need to calculate the bandwidth of the signal which has 2GFSK modulation. Do you think the code below is correct for ...
1
vote
1answer
815 views

How to send DMR SMS using MMDVM modem or hackrf?

I have a baofeng DMR radio with SMS feature, and since there is not much DMR radio owners in my area I want to do something myself. The easiest thing I can do I thought is to send myself some SMS as ...
1
vote
0answers
399 views

Capturing Bluetooth / WiFi on an SDR

I have a question, right before purchasing SDR for some tests: Commercial hardware for bluetooth (even Ubertooth) allows you to receive packets on a 1MHz channel. Which practicaly means that if you, ...
1
vote
0answers
102 views

Trouble with osmocom source

I'm having trouble running a simple flowgraph with an osmocom source and a qt gui sink. If I run the file with a waveform generator instead of the osmocom source, all is well, the plots appear as they ...
1
vote
0answers
69 views

How to limit frame transfer in Gnu Radio Companion?

I have as source a bit frame, then I modulate it, to finally transmit it with my HackRF. I can receive and decode it normally with another HackRF. However I would like to limit to a number of frame ...
0
votes
0answers
100 views

Writing “Wav” file in GNU Radio 3.9.0

I need to burn an audio file received from a computer sound card. But in the new version of the gnu radio, I found that the "Wav File Sink" and "Wav File Source" blocks were gone. ...
0
votes
0answers
62 views

RS41 weather balloon unable to decode data

Some times ago I tried to decode the signal from a weather radiosonde (RS41) passing in my area using a cheap RTL SDR (using both standard antenna and a home-made one, with similar result). The ...
0
votes
0answers
35 views

Ofdm carrier allocator block in gnu radio

I have some very basic question of the ofdm carrier allocation in gnu radio that am not understanding.please help me to understand. I want to pass a LTE based ofdm modulated signal simply like the ...
0
votes
0answers
148 views

Is there any 2.4 GHz tuner ICs for SDR receivers?

I have a hackrf one sdr, which i use to transmit test signals. I am using ISM bands, so I can omit transmitting my callsign, checking correct sub band (FM, digital) etc. And one of most interesting ...
0
votes
0answers
76 views

Gnuradio loopback flowgraph is not working

I found the below uhd_two_tone_loopback example (which is one of the gnuradio provided examples) and I am trying to run it, it runs but I can't receive signal. EDIT: I mean when I run the program I ...
0
votes
0answers
79 views

What the difference preamble and access code?

gnuradio packetize using access code for start sync packet, but another example attach the preamblee, so what the differences preamble and access code ?
0
votes
0answers
52 views

A gnuradio program that can output some arbitrary waveform read from a file containing I/Q values

I am trying to figure out how to create a gnuradio program that can output some arbitrary waveform read from a file containing I/Q values. I would highly appreciate any guidance in this topic. Simple ...