Questions tagged [software-defined-radio]

Radio devices that use digital signal processing in place of analog electronic components to manipulate RF signals.

Filter by
Sorted by
Tagged with
2
votes
2answers
176 views

No module named 'gnuradio'

I encountered with the "No module named 'gnuradio'" error while I was trying to run GnuRadio python code in my python web server. And this is my gnuRadio generated code: ...
17
votes
3answers
4k views

SDR sampling bandwidth - do the bits per sample matter?

I'm looking at data converter chips for a homebrew SDR design, and I see that I can choose not just the sampling frequency, but also the bits per sample. Obviously the sampling frequency has to be ...
3
votes
3answers
1k views

Broadband antenna for SDR radio

I recently bought a very wideband SDR receiver (DX-Patrol MK4, declared covered frequencies are 100kHz-2GHz). I'm experimenting with antenna designs because unfortunately I live in an apartment ...
10
votes
1answer
1k views

Why is dynamic range relevant for an SDR?

Sometimes I see dynamic range mentioned as a figure of merit for an SDR. For example, I know that the bits per sample used by the analog to digital converter can affect the dynamic range. Why do I ...
2
votes
1answer
194 views

Preamble of a garage door opener

After detecting the transmitted signal of a garage door opener with SDR, is it correct to assume the first repeating pattern of the signal is preamble? I only see two one and zeros with equal ...
11
votes
4answers
2k views

Is is possible to operate D-Star from a software-defined radio?

What is preventing a software-defined radio from transmitting the D-Star protocol?
6
votes
2answers
154 views

SSB offset determination?

Is there any algorithmic way to determine if the mixed frequency offset in an SSB SDR demodulator is wrong (too high or low), other than listening for funny sounding voices? (perhaps by checking to ...
3
votes
2answers
2k views

Choosing a wideband antenna design

On a previous question I asked about proper antenna design for wideband SDR receiver and ways to improve signal/noise ratio. Ideally the reciever has a range of 100kHz-2GHz. Keeping in mind is ...
7
votes
2answers
425 views

How to calculate if low-pass filtering is sufficient?

An answer on this question Suggested method for boosting 0.05 watt transmitter up to 10+ watts? suggests putting a filterless 19dB amplifier between the HackRF (or similar general-purpose SDR) and a ...
6
votes
1answer
946 views

Suggested method for boosting 0.05 watt transmitter up to 10+ watts?

Long time ham operator here, new to this particular challenge - I have a software defined radio transceiver that I'd like to try and use to make contacts on HF, in particular 20-meters. Tuning ...
4
votes
2answers
277 views

Sampling a 50 MHz Max Frequency 50 MHz BW Signal with a 50 MSps ADC

I paste below a superhetorodyne based Software Defined Radio Architecture for an Rx channel below. Suppose the IF signal has a max frequency of 50 MHz and 50 MHz IF BW. In that case, is it possible ...
10
votes
2answers
609 views

Can an amateur use cellular technologies with SDR?

Software Defined Radio is opening up many new possibilities for amateur digital modes. One family of technologies that interests me is cellular. 2G GSM voice/sms and 2.5G GPRS data has been proven to ...
10
votes
2answers
557 views

Multiple simultaneous tunings with SDR

I just found out about WebSDR, and I was wondering how is it possible that many listeners listen and tune to different stations simultaneously. Which components/technologies allow this, and how does ...
5
votes
2answers
711 views

How does rpitx generate arbitrary SSB data with a clock peripheral?

While it wasn't the first to do so, the rpitx software seems to be the most active and mature implementation of what its own comments call "a code fragment by PE1NNZ". The trick is explained in Guido'...
2
votes
1answer
295 views

Can HDSDR perform the work of Direwolf?

I have a setup in which Direwolf is used in conjunction with a Baofeng radio to basically send data (AFSK). My app connects to the TCP server provided by Direwolf, send him some data which then is ...
1
vote
2answers
1k views

How to best connect an FM transmitting GPIO pin to an antenna?

I'm trying to use a RaspberryPi3 as a FM transmitter, using pifm and/or PiFmRds to send audio in 88-108 MHz band. The RPi can then use the GPIO-4 pin to transmit between ...
0
votes
0answers
39 views

A gnuradio program that can output some arbitrary waveform read from a file containing I/Q values

I am trying to figure out how to create a gnuradio program that can output some arbitrary waveform read from a file containing I/Q values. I would highly appreciate any guidance in this topic. Simple ...