Questions tagged [software-defined-radio]

Radio devices that use digital signal processing in place of analog electronic components to manipulate RF signals.

17 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
6
votes
2answers
72 views

DIY SA612 + RTL-SDR HF receiver: good on laptop, but huge wideband noise on Raspberry Pi

I recently built a SA612 mixer for HF reception. I used an USB-frequency oscilator to shift the incoming frequency up by 28.8 MHz. I used a random wire antenna outside my balcony and connected it to ...
6
votes
1answer
144 views

SNR measurement for a BPSK/QPSK signal

I have created a software (gnuradio) that performs modulation/demodulation and supports a number of modulation schemes and error correcting codes. I'm in the process of evaluating the BER vs SNR for ...
3
votes
0answers
792 views

OFDM spectrum, HACKRF, and GNUradio companion

I am trying to analyze the spectrum of wifi spectrum. I getting a good OFDM spectrum with my HackRF at 2.412 GHz (from my first QTGUI Sink). But I get nothing out of OFDM Receiver. I was wondering ...
2
votes
0answers
40 views

Demodulating ISO14443 (part of NFC) using SDR?

I'm looking for info on demodulating both sides of an ISO14443 communication using a cheap SDR, preferably an RTL-SDR (R820T2+RTL2832U). The application is passively monitoring an NFC exchange for ...
2
votes
0answers
60 views

HackRF One and IoT overloaded?

I'm transmitting Z-Wave frames using HackRF One in loop, one frame every second. Has anyone clue why are some frames not transmitted? You can see several too long gaps between frames on Waterfall (...
2
votes
0answers
223 views

How to decode 2FSK signal with SDR?

I'm new to radio and SDR but, as a hobby project, I'm trying to decode a 2FSK radio signal received by an RTL-SDR that I sent using an SI4463 transmitter. The record file contains 3 packets, but I'm ...
2
votes
0answers
434 views

LimeSDR Mini + Raspberry Pi 3 B+ Transmission problem

I am new at this. I would like to transmit an audio signal cleanly using WBFM but I see two signal peaks occur around my fundamental frequency when I start transmitting. In this case I am using a ...
2
votes
0answers
316 views

Does anyone repair Flex radios other than Flex Radio?

A local ham that I have an evening sked with on 75m (Paul, W0EBV) sent his Flex 5000 SDR transceiver to Flex Radio Systems to get it repaired a few months ago. However, it seems that Flex is either ...
1
vote
1answer
68 views

audio problem with SDR on MacOS

I'm experimenting with SDR on MacOS High Sierra. Trying both CubeSDR and GQRX and experiencing similar issues with both. The applications seem to work, but the audio is choppy and chipmunk-like. ...
1
vote
0answers
74 views

Capturing Bluetooth / WiFi on an SDR

I have a question, right before purchasing SDR for some tests: Commercial hardware for bluetooth (even Ubertooth) allows you to receive packets on a 1MHz channel. Which practicaly means that if you, ...
1
vote
0answers
49 views

How FEC works on GNU Radio

I am new to GNU Radio. I need some reference to how to use FEC block in GNURadio. When I try to make encoder and decoder without modulation, its work as well, but when I using modulation and add ...
1
vote
0answers
62 views

Trouble with osmocom source

I'm having trouble running a simple flowgraph with an osmocom source and a qt gui sink. If I run the file with a waveform generator instead of the osmocom source, all is well, the plots appear as they ...
1
vote
0answers
55 views

How to limit frame transfer in Gnu Radio Companion?

I have as source a bit frame, then I modulate it, to finally transmit it with my HackRF. I can receive and decode it normally with another HackRF. However I would like to limit to a number of frame ...
0
votes
0answers
38 views

Is there any 2.4 GHz tuner ICs for SDR receivers?

I have a hackrf one sdr, which i use to transmit test signals. I am using ISM bands, so I can omit transmitting my callsign, checking correct sub band (FM, digital) etc. And one of most interesting ...
0
votes
0answers
37 views

Gnuradio loopback flowgraph is not working

I found the below uhd_two_tone_loopback example (which is one of the gnuradio provided examples) and I am trying to run it, it runs but I can't receive signal. EDIT: I mean when I run the program I ...
0
votes
0answers
34 views

What the difference preamble and access code?

gnuradio packetize using access code for start sync packet, but another example attach the preamblee, so what the differences preamble and access code ?
0
votes
0answers
42 views

A gnuradio program that can output some arbitrary waveform read from a file containing I/Q values

I am trying to figure out how to create a gnuradio program that can output some arbitrary waveform read from a file containing I/Q values. I would highly appreciate any guidance in this topic. Simple ...