Questions tagged [rf-power]

Questions about power ratings and restrictions, including maximum power by law or for certain components, or about calculating power in certain situations.

Filter by
Sorted by
Tagged with
2
votes
2answers
121 views

Output power from the TX/RX port of the USRP N210 decreases as the frequency increases

I am trying to build an FMCW radar using a USRP N210 with a CBX40 daughterboard. I generate a sweep from 1.5GHz to 5GHz. According to their respective datasheets, the daughterboard and the USRP should ...
1
vote
3answers
533 views

How does the Maximum Power Transfer Theorem relate to RF power amplifiers?

The Maximum Power Transfer Theorem says that maximum power transfer occurs when the source impedance equals the load impedance, when the power transferred to the load is 50%, the other 50% being ...
0
votes
2answers
86 views

Why is there so little difference in the gains of Yagi Uda antennas with omnidirectional antennas? Shouldn't the power at the back be at the front?

Consider an omnidirectional antenna with X dBi gain. Intuitively I understand that the power that would have been dispersed in now-dead directions is directed around the antenna. What I don't get is ...
0
votes
0answers
35 views

How do you take into account the SNR of a transmitter in a fade margin?

I have a fade margin for a RF bridge, but it only compares the sensitivity of the receiver to the received power - or alternatively calculates the Eb/N0 from the net received power divided by the ...
-1
votes
1answer
69 views

Acoustic Communication issues [closed]

[![I've attached schematic, I am connecting transducer directly to that header pins on receiver side. On transmitter side I am connecting op-Amp to boost voltage to +10v -10v.][1]][1]I am working on ...
8
votes
4answers
5k views

What is the power increase required to double the range of RADAR?

Studying for a Pivate Pilot's Licence (PPL) and I've hit something in the study material that doesn't make sense to me. Typical of the PPL study material, it's quite shallow, so the full explanation ...
1
vote
2answers
61 views

Is power output or something else to blame for my duplexer failing?

A Ham buddy of mine and I were trying to setup a UHF repeater in our area due to a lack of them. We had two Motorola CDMs, one a 1250 and one a 1550, and we purchased a $200 or so reject only duplexer ...
4
votes
2answers
249 views

Is the 1.5kW power limit per antenna? What about antenna arrays?

My son KJ7NLL just got his general, and while we don't (yet?) have plans to transmit at 1.5kW, he asks if the 1.5kW limit is per-antenna? If it is per-antenna, and you use an antenna array of 8 ...
11
votes
4answers
7k views

What is dBm and why is it used rather than watts?

Reading through an RF power amplifier datasheet, I found the sheet only referenced dBm output power, rather than watts. What is dBm? How do I convert it to watts? Why, or when, would you use dBm to ...
5
votes
1answer
64 views

Acceptable RF radiation exposure to electronic equipment

I'm wondering if there are any general guidelines or rules of thumb about the exposure of electronic equipment to RF transmissions, 150 MHz - 900 MHz. The background is that we are looking to install ...
3
votes
1answer
154 views

Troubleshoot ICOM IC-745 intermittently shows no power on transmit

I have an old IC-745 I bought used last year. Recently it seems to be malfunctioning intermittently. It is receiving well on all bands as far as I can tell. Sometimes when transmitting, there is no RF ...
0
votes
0answers
28 views

Setting the maximum Tx Power value for the USRP transmitter

In order to simulate the measurements on the computer (in the WinProp environment) I have to set the maximum Tx power: To find out what the transmitter signal power is, I checked it on the spectrum ...
6
votes
3answers
10k views

How do I power my radio in a vehicle mobile install?

I want to install a 30W mobile UHF radio in my car. I already have an antenna and mounting bracket - but how do I get power to this radio? It has an SAE bullet connector on the back - do I just need a ...
2
votes
6answers
1k views

How to make an RF probe for accurate power measurement at QRP power levels?

Typical SWR meters don't measure forward power very accurately at the lower end of the scale, which can be a real problem at QRP power levels. Better power meters like the Bird model 43 are expensive,...
1
vote
2answers
112 views

Increasing communication range by boosting output and input power

ORIGINAL QUESTION I am trying to increase the range of communication between two SDRs to simulate near space communication. The output power of TX is 10dBm but I would need 37dBm for near space ...
3
votes
3answers
1k views

Yaesu FT-891: power drops to 50% when TNR is ON and SWR is 1.5:1

I noticed a weird behavior of my Yaesu FT-891 transceiver. I'm using it with an external autotuner mAT-30 (120W SSB/CW, 30W PSK31), which is compatible with Yaesu FC-50. When I connect a 100W 50 Ohm ...
0
votes
2answers
73 views

Repeater design using round robin transmitters to increase duty cycle?

I would like to build an FM repeater using a short stack of Kenwood TK-890H rigs adjusted to 70cm USA amateur band, but the model has a 100W rating with a duty cycle of only 20%. 20% isn't nearly ...
2
votes
5answers
170 views

Does 3 W vs 5 W TX power make a huge difference in QRP CW operation?

I've bought the QCX+ 40 m band radio. I will be powering this off a 12 V battery. I read on the manual the RF power at 12 V is just 3 W whereas on 15 V it is 5 W. Should I buy a boost converter for ...
0
votes
2answers
146 views

Where can I find a table listing the maximum PEP per band?

I'm building myself an Excel Cheat Sheet.
1
vote
1answer
118 views

What is the maximum antenna cable length allowed in GNSS application?

I am beginner in designing GNSS receiver design and facing concern while testing the high precision GNSS survey.I am using GNSS survey grade antenna for my GNSS receiver application testing, the ...
0
votes
3answers
693 views

Can a carrier operated relay be used for T/R switching in a HF linear amplifier?

I am building the T/R switching circuit for an HF linear amplifier covering 80m band to 20m band. The current circuit takes a potential-free contact from the exciter and use this contact to turn on/...
0
votes
2answers
252 views

Can a Loop Antenna send and receive 10,000 miles away

Can we expect a Loop Antenna such as a Chameleon F-Loop Antenna transmit and receive from the USA's midwest to Australia on HF using an average 100 watt SSB transmitter and an average receiver? If so,...
9
votes
2answers
935 views

Importance of Ferrite Size in Coax Choke Balun

The question is quite simple: When making a coax choke balun, does the size of the ferrite matter, and if so, why? I have seen design notes that say to use a single FT240-43 toroid for powers up to ...
6
votes
1answer
251 views

SNR measurement for a BPSK/QPSK signal

I have created a software (gnuradio) that performs modulation/demodulation and supports a number of modulation schemes and error correcting codes. I'm in the process of evaluating the BER vs SNR for ...
1
vote
2answers
281 views

Power vs. Bandwidth

A 10 watt transmitter is transmitting a 700 hz tone in a 3 kHz wide band. If the power is increased to 1000 watts will that not increase the bandwidth if the data (700Hz tone) remains constant? What ...
1
vote
1answer
169 views

Signal power measurement

I have a radio with a nominal output of 1-30mW (frequency dependent) and amplify this with a 21.8dB capable amplifier (frequency dependent, but should be ~150mW). The signal output then passes through ...
2
votes
2answers
108 views

Estimating near-field electric field strength at LF (137 kHz)

I'm experimenting with low frequencies, but due to the inherent nature of LF, I strive for more transmit power and bigger antennas. Now of course I want to comply with regulations, which allow (in my ...
1
vote
1answer
127 views

How to measure the power emitted from an HF antenna in near-field WPT?

I'd like to estimate the power density from a 13.56 MHz power source in a near-field WPT (wireless power transfer) scenario. Using a spectrum analyzer with a receiving antenna will give the E-field ...
0
votes
1answer
135 views

Calculating receive wattage given transmit power, antennae dBi and path loss

I would like to understand how to calculate receive wattage given the following (excluding feeder loss and SWR): Transmit 50 dBm (100W) => 24 dBi directional antenna => 30 dB path loss => 24 dBi ...
5
votes
1answer
1k views

How does power received by a dipole relate to electric field intensity?

Let's say there's a transmitter far away, and I'm going to receive the transmitted signal. To keep things simple let's further say the transmitted signal is a pure, unmodulated sine wave. Further, let'...
1
vote
3answers
495 views

How safe is 100 watts on 2-40 meters?

So I have the misfortune of being an apartment dweller. I know that 50 watts is pretty safe as it is what first responders use on 2 meters. Am I really going to have to run around with an analyzer ...
0
votes
2answers
144 views

measures for quantifying non-linearity of a HF linear power amplifier

I am DIYing a class-AB HF Linear Power amplifier. How to quantify the non-linearity of this amplifier. What are the common measures of non-linearity as applicable to RF power amplifiers? How to ...
0
votes
2answers
626 views

What kind of filter should be used at the output of HF linear amplifier?

I am looking for a output filter to use with a HF linear amplifier called miniPA70 which is available through several online auction sites. The circuit is available here : http://iu3idf.blogspot.com/...
1
vote
1answer
633 views

SO-239 (UHF) vs N connector power handling on 160m

I am curious how much CW power an N connector or SO-239 connector will handle on such a low frequency like 160m band. I know on VHF they will probably handle about 800W before getting too warm. I ...
2
votes
1answer
323 views

Legal aspects of the HackRF one / SDR in Switzerland?

I would like to know, what I can legally do with SDR / a Hack RF One in Switzerland? What are the limitations concerning sending and receiving? Do I need any licenses for that? If so, which ones, ...
5
votes
2answers
225 views

Can I have a signal generator on while it's not connected?

The unit in question is an Elecraft XG3 test signal generator. It puts out anywhere from -107 dBm to 0 dBm. Is it safe to have these signal generators on and transmitting while not connected to ...
5
votes
3answers
1k views

Cheap antenna for new HF HAM

I just got a 100W HF radio and I am new at this. What is the cheapest antenna I can hook up without burning up my radio or shocking myself?
-4
votes
1answer
108 views

Wifi inside a rocket

I want to understand, as most rocket uses LAN cable and switches to communicate between stages. Is it possible to replace with WiFi? Although it's will be complex system but one idea to make each ...
0
votes
1answer
225 views

Passive antenna system as a Wi-Fi repeater [duplicate]

I want to extend WiFi signal using a passive repeater between two isolated boxes (have to make both box wireless). Transmitter antenna from box A is placed in the gap between box A and B. In the same ...
3
votes
2answers
455 views

Using approximate signal strength at a distance to estimate reception strength of a radio station

I have some historical data on radio stations, but unfortunately, the dataset only has these variables: the power of the transmitter, in watts the coordinates of the radio tower Unfortunately, I ...
3
votes
1answer
149 views

Restoring full output power to rig with tube finals

I have a TS-830S that was initially doing about 60W in CW at 10m and 70W at 40m. I've heard these things are capable of at least 100W. Determined, I started doing research on what components to look ...
1
vote
2answers
114 views

Matching a 188 ohm antenna to an unbalanced input that expects a 50 ohm antenna

I am new to RF field and trying to use an Archimedean Spiral Antenna design from this paper to capture 915MHz RF for the P2110B power harvester chip. The estimated antenna impedance is 188 Ohm (see ...
7
votes
1answer
721 views

Double power-handling ability of RF amplifier output transformer

I want to base the output network for a 500W push-pull HF amplifier on "A 250W Broadband Linear Amplifier" described in Chapter 17 of the 2014 ARRL Handbook. I need advice on whether and/or how the 1:...
1
vote
0answers
83 views

Parasitic inductance of relay contacts

I need to switch a bank of filters operating on bands from about 2MHz to 30MHz. The parasitic series inductance of the relay contact system will have an effect on the performance of my system. ...
3
votes
2answers
253 views

Determining whether signal meets the 12 dB SINAD voltage

The specification for a certain radio receiver says: Typically 12dB SINAD NBFM for 0.15uV at 145MHz. If I understand correctly, this means that the received radio wave should have a voltage level of ...
6
votes
1answer
228 views

Is it safe to run two barefoot rigs on one antenna with an AB switch?

I have a Daiwa CS-201A two position switch. The single side is connected to by quarter wave vertical (40m). The A and B sides are connected to an IC-7300 and TS-830S. The switch is claimed to have ...
5
votes
2answers
3k views

How to find or derive the maximum safe input power to a receiver?

A number of my RF devices have a specified safe maximum input power, for example: "The maximum RX power of HackRF One is -5 dBm. Exceeding -5 dBm can result in permanent damage!" source "If you look ...
6
votes
2answers
384 views

distance between shack and antenna

I am putting a 40m antenna in my attic and I was wondering would it be safe to have a shack in the room right below the attic (10ft of coax or less) or should I have my shack in the basement/ground ...
6
votes
2answers
273 views

Does amateur radio induce a health risk?

Electromagnetic Exposure wise, does Amateur radio (Particularly 1.8 to 440 megahertz) induce a health risk due to RF radiation? Other than the Maximum Permissible Exposure (MPE) limits, which will ...
2
votes
1answer
148 views

Attenuator Cascaded Connection

PAT1220-C-10DB-T5 is a 10dB attenuator. (This chip is just an example, it could be any other component as well). Can I simply connect 3 of them in series in a PCB design to make my cheap 30dB ...