Questions tagged [receiver]

Use this tag for questions about the theory and structure of receivers.

Filter by
Sorted by
Tagged with
4
votes
2answers
185 views

Does the output of a BFO for a short wave receiver have to be exactly a sine wave?

I want to build an external beat frequency oscillator (BFO) for an old valve Eddystone receiver I have. There are many circuits for BFOs on the internet, they are mostly similar, the idea seems simple ...
4
votes
1answer
114 views

Commercial Loopstick Antenna Manufacturers?

I am an electrical engineer working on a product that needs a loopstick antenna. I had thought that AM radios were so commoditized that I'd be able to find an off-the-shelf vendor. However the closest ...
5
votes
2answers
635 views

How to calculate power transmitted by monopoles?

I only studied monopole in sending mode or receiving mode alone but never in both modes together, I have this question which says: Two vertical λ/4 monopoles are parallel to each other with 20 ...
2
votes
0answers
51 views

Buzzing FM interference

What kind of interference or other receiver issues can cause a constant buzzing noise (picket fence lines in the audio spectrum) in the demodulated audio of a received NFM VHF signal? With AM, it ...
0
votes
1answer
34 views

Combining two CFU455IT +/-2kHz (4kHz) ceramic filters to get a +/-1.25kHz (2.5kHz) filter for SSB

Can I put two of these cheap (less than 3USD) and common CFU455IT +/-2kHz (4kHz bandwith -6dB ) ceramic filters in series to get a lower bandwidth good for SSB TX? If I'm correct I will get -12dB at +/...
2
votes
1answer
167 views

FSK real world application BER

I have designed a receiver for FSK reception in 434 MHz ISM band. For this I used USRP1 and GNU Radio. Now, I would like to measure performances of my receiver. For this purposes I did following: I ...
5
votes
5answers
6k views

Shortwave Antenna Listening with Portable Receiver Like TECSUN PL-660?

I have a Tecsun PL-660 (link is to the manual) has the usual AM/FM radio telescoping internal antenna, and a 1/8th-inch jack for an external shortwave antenna. There appears to be no facility for ...
5
votes
4answers
1k views

Efficiency of short dipole receiving antenna

For a transmitting dipole antenna, its length is important. If it is close to half the wavelength, it will be efficient and most of the input power will be radiated. How important is the length of ...
1
vote
1answer
40 views

PSR500/Pro106/WS1040 Phase II Upgrade?

I want to know if one can upgrade the hardware chips/ the CPU/DSP inside police scanners to do Phase II. I know they cannot do Phase II due to hardware/software limits but if whistler can upgrade ...
1
vote
4answers
948 views

what are the alternatives to LM387 and SA602AN?

I am building a 20 Mhz RF receiver out of the NASA radio JOVE instruction manual and they have recommended the use of LM387 as an audio amplifier. SA602AN as mixer IC:
2
votes
1answer
62 views

Baofang uv-5rA/ repeater trouble

I programmed my Baofang UV-5RA radio to my local repeater about less than a 1/4 mile away. When I cue the mic and release, I get a signal from the repeater. However, I can only hear people if I have ...
3
votes
3answers
2k views

How to receive a signal from multiple sources simultaneously (helical antenna)

I'm working on a system (theoretical at the moment) whereby I wish to receive data from multiple sources all transmitting at the same time. I've read that a helical antenna is capable of this. I'm ...
5
votes
1answer
141 views

Looking for a book that contained a circuit for receiving (literally) underground amateur radio transmissions

In this comment in Earth Science SE I've said: This is a really cool question! I remember (a long time ago) reading about electromagnetic waves inside conductive soil that travelled near but below ...
5
votes
3answers
667 views

Substitute for 455 kHz Ceramic filters in new designs

I am looking to design a dual conversion FM receiver/power meter for t-hunting similar to the MK4 sniffer using 10.5 MHz and 455 kHz IF. In my research it appears that manufactures have stopped ...
2
votes
3answers
410 views

What causes my direct conversion 80m receiver to receive AM broadcasts?

I am making a Direct conversion receiver from this circuit at this website. I made it for the 80m band and I changed: The frequency of VFO to about 1.75 MHz L1 and L2 to a bandpass filter for 80m ...
1
vote
2answers
91 views

Advantages of IQ mixer versus baseband sampling SDR architectures?

What might be the advantages, if any, of HF SDR architectures that use a mixer between the ADC/DAC and RF, versus those that sample or generate RF directly at baseband with a fast ADC or DAC? Are the ...
0
votes
1answer
51 views

Calculating receive wattage given transmit power, antennae dBi and path loss

I would like to understand how to calculate receive wattage given the following (excluding feeder loss and SWR): Transmit 50 dBm (100W) => 24 dBi directional antenna => 30 dB path loss => 24 dBi ...
3
votes
4answers
923 views

Is it normal for mini shortwave radios to not have any reception in a major city?

I'm new to radios. Just bought the mini Eton which has FM/AM/SW and while FM & AM work I have never received a single station on SW1 (5.9 - 10 MHz) or SW2 (11.65 - 18 MHz). Is that normal? Will ...
0
votes
0answers
16 views

What configuration of a BJT IF amp can I use for a superhet receiver?

I am making a superhet SSB CW receiver with a crystal filter on the input after the mixer. Do I have to use IF transformers as the coupling method? Or can I use capacitor coupling with resistors as ...
2
votes
0answers
98 views

Unknown kit from DK0TV

When my father - who became a ham years after I did - passed away, I found an unstarted project (board + components), which I only re-discovered again years later. The board is marked DK0TV-001, and ...
13
votes
1answer
2k views

How would a time-difference-of-arrival receiver with two antennas know which side the signal is from?

An easy TDOA design by Byonics was published with the following schematic: It appears that the antennas are switched at a rate of 640Hz, which allows a 640Hz tone to be heard in the radio when the ...
1
vote
2answers
2k views

Is there a way to find out the location where a radio signal is intercepted?

I am a software engineer and a noob to radio. Is there a way to find out the location where a radio signal is intercepted? That is, the location where somebody is eavesdropping on my wireless ...
0
votes
0answers
64 views

Is there any 2.4 GHz tuner ICs for SDR receivers?

I have a hackrf one sdr, which i use to transmit test signals. I am using ISM bands, so I can omit transmitting my callsign, checking correct sub band (FM, digital) etc. And one of most interesting ...
4
votes
4answers
2k views

What are some equivalents of a BF199 transistor?

I'm planning to build an FM radio receiver using the instructions on http://www.instructables.com/id/Build-your-own-Crude-FM-Radio/ The schematic uses a BF199 transistor which is marked "obsolete" by ...
1
vote
2answers
293 views

Any way to block one FM station

I live next to a 100 kW FM transmitter, 600 feet away transmitting on 103.7 MHz. It is south east and most other station I want to listen to are in other directions. This station comes though most ...
2
votes
2answers
175 views
8
votes
2answers
11k views

Connect two receiving antennas to the same radio

I have built a 1090 MHz ADS-B antenna roughly following some video instructions. It appears to work reasonably. However, because of how it is placed, it captures signals for more or less a half of ...
6
votes
2answers
112 views

Why aren't “ghosts” and intersymbol interference due to unmatched impedance (high SWR) a concern for HF receivers?

In amateur radio, we care about impedance matching when we need to keep the load within the equipment's specification (for best performance, or just to avoid damaging a transmitter), when we want to ...
3
votes
3answers
356 views

Iskra sst 2030 radio speaker plug

I was asked by a friend to take a look at an old 70-80s Iskra sst 2030 (ex Jugoslavian-slovenian company) radio. The radio seems to work fine but I can't understand which plug it uses for speakers. ...
2
votes
1answer
77 views

How much field strength to blow out a receiver?

I was wondering what calculations would need to be performed to find out if a receiver will blow out in the given conditions. Portable AM receiver with ferrite rod antenna 200 ft away from MW antenna ...
1
vote
2answers
75 views

How is frequency selection (tuning) accomplished in a direct conversion receiver?

How is frequency selection (tuning) accomplished in a direct conversion receiver ? A crystal filter can't be used is that correct ? Because there is no IF to mix with the incoming frequency band ...
0
votes
1answer
94 views

Locate a ball 1000 times a second

I want to locate a small ball in the air 1000 times a second. The ball is thrown from the ground and then flies in the air for 0.5 seconds until it lands. Distance from the location instrument is 1 ...
2
votes
3answers
155 views

Will a “crystal set” work with an untuned RF amp stage?

In my ongoing process of building up to a homebrewed general coverage receiver/transceiver, a first step might reasonably be a crystal set, where a tuned circuit and simple, or even improvised, ...
20
votes
8answers
42k views

How can I avoid accidentally transmitting with a Baofeng UV-5R?

I don't have $500 for a radio scanner. If I know the few (analog) frequencies that I would like to listen to, I think one can use the Baofeng UV5R (which doesn't cost much). The only problem is that ...
5
votes
3answers
15k views

How to improve reception with a headphone-cord antenna?

I have a headphone and a cellphone that has built-in FM radio, and the headphone acts as the radio antenna. but my problem is the radio stations I listen to are very far from my place, good thing ...
2
votes
0answers
88 views

Has this regeneration control been done?

I'm planning to build a two-tube reflexed RF regen receiver soon. I'm examining methods of controlling the regeneration — it needs to be possible to both initiate and halt oscillation in all bands (I ...
1
vote
0answers
39 views

Problem to paralel tv digital reciever [closed]

Here is my C-Band parabolic tv digital receiver. As shown by the pictures, the incoming coax cable (INPUT) connected both the outer and the core. One goes to digital receiver 1 (receiver 1), and ...
2
votes
1answer
175 views

How does this circuit work? Why is the antenna connected to the output of the amplification stage?

What is the function of the configuration of R1, C3,C10 and R3? How does the LC tank in this circuit work?
0
votes
3answers
126 views

How to make simple AM detector using an LED?

I'm new to amateur radio, and as a beginner project, I wanted to use some of the basic components I have to create an AM receiver. Anyway, what I'm trying to do is create a simple AM receiver that ...
0
votes
1answer
57 views

Unusual modulation

I've been writing a SciFi story, and it calls for something very unusual to happen. I'd like to check this idea for plausibility, but as I'm not a radio ham myself, I don't know if this already exists ...
2
votes
1answer
195 views

Frequency Display for Old Tube Radio

I have a Hallicrafters S-120 1960s vintage vacuum tube receiver (an "All American Five" superhet with solid state rectifier replacing one of the "five" tubes). It works well, doesn't have excessive ...
1
vote
1answer
90 views

Radio antenna for my FM receiver / Android FM

I want to make a radio antenna at home which will be able to receive all FM frequencies for my FM radio or Android FM. How do I make it? Frequency it can catch : 88 - 108 MHz Thanks.
3
votes
2answers
383 views

How do I listen to the amateur radio satellites?

I'm new to amateur radio, and I would like to listen to those satellites in the orbit. Where do I start? What types of amateur radio satellites exist?
3
votes
2answers
155 views

Determining whether signal meets the 12 dB SINAD voltage

The specification for a certain radio receiver says: Typically 12dB SINAD NBFM for 0.15uV at 145MHz. If I understand correctly, this means that the received radio wave should have a voltage level of ...
1
vote
1answer
43 views

Passive receiver power needs & data rate

I'm working on a project to design a space-based low frequency array. It will only be receiving signals, and it will operate between 10MHz - 100MHz. It is made of short wave crossed dipole antennas. I ...
3
votes
2answers
2k views

How to find or derive the maximum safe input power to a receiver?

A number of my RF devices have a specified safe maximum input power, for example: "The maximum RX power of HackRF One is -5 dBm. Exceeding -5 dBm can result in permanent damage!" source "If you look ...
5
votes
2answers
75 views

Why do receiver sensitivities vary so much with frequency?

I was looking for a 2.4 GHz WiFi antenna to catch a weak free WiFi signal, and amplify it so I can use it. I found Ruckus Metroflex NG, which can receive signals down to -108 dBm. Which is amazingly ...
6
votes
1answer
204 views

Pentode vs. Triode in Tuned RF Reflex Receiver

I'm planning on building a multi-band vacuum tube receiver. I've got a circuit diagram in hand for a two triode twin reflex with optional regeneration (P.E. Edelman, Reflex Radio Receivers, 1924, Fig....
6
votes
1answer
142 views

Why does adding 50-ohm BNC Ethernet terminator(s) in parallel to my 4-element yagi improve my radio's reception? (70cm)

I have this radio, with a rubber duck antenna, and a repeater twenty miles away to my north-northwest. If I set my radio on the top of a cabinet in my bathroom, I receive the repeater fine. I can't ...
12
votes
4answers
10k views

How To Join Packet Radio BBS

I'm a complete newbie here, and on the Southeast Coast of the USA. I don't even own a ham radio yet. Some preppers and I got to talking about a dystopian time of Internet collapse where shortwave ...