Questions tagged [impedance-matching]

Questions about fixed impedance matching networks, the necessity of impedance matching, etc.

Filter by
Sorted by
Tagged with
2
votes
1answer
149 views

How is impedance matching related to balance and common-mode currents?

Does a good impedance match imply good balance and lack of common-mode currents? Does a poor impedance match imply poor balance and excessive common-mode currenst?
2
votes
1answer
78 views

How to consider the influence from the PCB that a small antenna is mounted on?

The small antenna itself has an $S_{11}$ of -3 dB around MICS band (verified with simulation and network analyzer). In application, the antenna is mounted on a transceiver PCB of 30*15*0.8 mm which ...
2
votes
1answer
91 views

Inductors for Impedance Matching

I need to impedance match an IF mixer circuit to a 10.7MHz crystal filter. One of the inductors was calculated to be 44 $\mu$H. So I need a relatively large value inductance in a small package to fit ...
2
votes
1answer
173 views

Dual Band Antenna Matching

I am building a wideband dual band omni for school. My antenna is about 2m long. The antenna length basically has two sections (divided by ports) - from 0 - 1.8m (This length is for 20-180MHz) and ...
2
votes
1answer
313 views

What is this matching technique called?

I've had this suggested to match 50 ohm coax to a lower feedpoint impedance, like a vertical, especially mobile shortened verticals. What's it called? simulate this circuit – Schematic created ...
1
vote
2answers
607 views

Exactly why do some SWR meters give a changing reading depending on the length of coax used to connect to an antenna?

Following is my understanding of some theory and the questions are at the end. Is this right ? ... A standing wave is an AC waveform oscillating at a particular frequency which has a varying ...
1
vote
2answers
115 views

Removing the whip on a 2m/70cm antenna makes no difference

Today I was trying to measure the SWR of a new aerial on my car which has 3 loading coils. Whilst doing this I took the whip out on the top to see how drastically I might have needed to cut the ...
1
vote
2answers
850 views

Impedance matching between antenna and load - Theory and Practice?

I'm trying to do impedance matching between my PCB antenna and my circuit. My PCB antenna has a measured impedance of 49.4 - j8.1 ohms. The operating frequency is 915 MHz. The goal of matching is to ...
1
vote
2answers
45 views

RF PCB Design Difference Between Controlled Impedance Track and Impedance Matching Circuit

Im new on RF circuit designing. Im designing an circuit with GSM and GPS capabilities. I know when using high frequency signals the RF traces must be impedance matched. Now what I understand is, I can ...
1
vote
1answer
269 views

Intermittent High SWR

Using a Cushcraft MA5B beam, when I apply high power from an amplifier, the SWR will go up and down intermittently. Something is breaking down at high power (200-500 W). I have a new coax feedline, ...
1
vote
3answers
287 views

How does the Maximum Power Transfer Theorem relate to RF power amplifiers?

The Maximum Power Transfer Theorem says that maximum power transfer occurs when the source impedance equals the load impedance, when the power transferred to the load is 50%, the other 50% being ...
1
vote
1answer
441 views

Can I connect a 75 ohm antenna to a 50 ohm radio?

I have been looking for an affordable yagi antenna to use with a dual band handheld radio and I came across some very inexpensive VHF/UHF (HDTV) antennas. They are all 75 ohm though. Is it ok to use a ...
1
vote
2answers
67 views

What would the power at output at a distance of 1cm when transmitted at a power of 1dBm from the transmitting antenna?

If the transmitter and receiver are placed one centimeter apart, what would be the power at the receiving end if the tranmission power is 1dBm? Consider an omnidirectional antenna. And if it is a ...
1
vote
2answers
93 views

Matching a 188 ohm antenna to an unbalanced input that expects a 50 ohm antenna

I am new to RF field and trying to use an Archimedean Spiral Antenna design from this paper to capture 915MHz RF for the P2110B power harvester chip. The estimated antenna impedance is 188 Ohm (see ...
0
votes
2answers
689 views

Understanding RG6-75 ohm Cable Impedance

Here is my measurement to a piece of RG6 cable. It is around 30cm cable. On the shield is written COAXIAL CABLE 5C-2V 75 ohm. From my measurement I got data as below: From that table, we can see that ...
0
votes
2answers
103 views

How to use 75ohm (RG6) coax?

I know that there have been many similar threads on this, but I still need clarification. At the moment, the only thing I have is a 500' roll of RG-6 and a (very) tight budget, and I should be ...
0
votes
1answer
87 views

How to characterize and select UHF linearly loaded antennas?

Q1.1: Why can a helix calculator not be used for linearly loaded antennas? Those online calculators suggested that the turn pitch/wavelength should be around 0.25. However, a typical linearly loaded ...
0
votes
1answer
55 views

SWR jumps to maximum of gauge

(I'm asking this in the context of a Cobra 29LTD CB, but I think that it also applies to amateur radio in general.) In SWR mode, the needle swings all the way to the right, hitting the limit. The (mag ...
0
votes
1answer
29 views

Obtaining S parameters using S11 measurements?

Is it possible to obtain the S-parameters of a circuit with only S11 measurements (S11 measurement with a VNA)? My gut tells me that it should be possible by connecting open, short and characteristic ...
0
votes
2answers
200 views

What kind of filter should be used at the output of HF linear amplifier?

I am looking for a output filter to use with a HF linear amplifier called miniPA70 which is available through several online auction sites. The circuit is available here : http://iu3idf.blogspot.com/...
0
votes
1answer
212 views

NFC coil matching - Q factor improvement

I have been trying to match my NFC reader coil of size 20*20 cm with a three element circuit - one capacitor in series, another in parallel and one resistor in parallel. I have been using Texas ...
0
votes
1answer
2k views

Input and output impedance of antenna/circuit: theory and measurement methods?

As illustrated in my previous post, I got stuck with the matching circuit between an receiving antenna and my circuit, including a rectifier and sensory circuits. I got confused with input and output ...
0
votes
0answers
36 views

Which specification is exceeded for a transistor output stage in a transmitter when there is a high SWR? [duplicate]

For a transmitter which has an output stage which uses one final output power transistor, when the SWR is high, it's common knowledge it seems that the output transistor can get hot and fail due to ...

1
2