Questions tagged [impedance-matching]

Questions about fixed impedance matching networks, the necessity of impedance matching, etc.

Filter by
Sorted by
Tagged with
1
vote
1answer
252 views

Intermittent High SWR

Using a Cushcraft MA5B beam, when I apply high power from an amplifier, the SWR will go up and down intermittently. Something is breaking down at high power (200-500 W). I have a new coax feedline, ...
8
votes
1answer
294 views

SWR Measured at the Transmitter versus SWR at the Antenna

It is fairly well understood that due to transmission line losses, the SWR as measured at the transmitter will be less than the SWR at the antenna. Some of the new antenna analyzers and some vector ...
9
votes
1answer
214 views

Does Coax Limit the Maximum SWR a Transmitter 'Sees'?

A recent discussion about SWR led to the assertion that a length of coax cable will ultimately limit the SWR to which the transmitter will be exposed. By experimenting with an SWR calculation tool ...
3
votes
1answer
1k views

Is ladder line necessary when using a non-resonant dipole through a tuner?

I've heard if I have a dipole of some arbitrary length, or a random wire, the SWR can be very bad. An antenna tuner can present a decent match to the transmitter, but the SWR on the feedline will be ...
2
votes
3answers
720 views

SWR, overall, is too high

This is a sort of follow-on question from my tuners in series question. The problem I am ultimately trying to solve is this: I am using a manufactured end-fed, half-wave 40m antenna. The ...
2
votes
3answers
756 views

How do I set up my radio for an antenna tuner?

I recently acquired an MFJ Versa Tuner II model MFJ-949D as well as a Kenwood TS-430S radio. The instructions for the tuner state (in part): For optimum operation of the MFJ-949D, the transmitter ...
2
votes
2answers
135 views

Antenna experimentation

I want to make a DIY antenna for my Kenwood TH-F6A. Is there any danger of damaging the radio (i.e. by trying an antenna that is unsuitable), or is it safe to experiment?
3
votes
3answers
989 views

What is the output impedance of a typical solid state ham transmitter?

I've often heard that the output impedance is 50Ω, and the load impedance should be matched to that and also 50Ω. While the reasons for the load impedance to be 50Ω are clear, is the output impedance ...
4
votes
1answer
232 views

What kind of losses do you get from an LC network matching the antenna's impedance?

If you have a transmitter that is perfectly on your frequency but you have an antenna with some impedance what types of losses, and of what magnitude, will you expect from a tuner in between your ...
2
votes
2answers
1k views

3 way coax split / impedance match

I would like to split a coaxial feed line 3 ways, maintaining 50 Ω impedance. I know how to do this 2 ways; you use 1/4 wavelength 75 Ω coax as matching stubs. I know how to do this 4 ways; you do 2 ...
2
votes
1answer
170 views

Dual Band Antenna Matching

I am building a wideband dual band omni for school. My antenna is about 2m long. The antenna length basically has two sections (divided by ports) - from 0 - 1.8m (This length is for 20-180MHz) and ...
2
votes
3answers
201 views

Do stub matching techniques still produce some loss?

I am using a double stacked Yagi-Uda antenna with about 57 Ω impedance. The 50 Ω feed line (coaxial) cables are combined using a tee connector. I observed, at the output of the tee connector, an ...
2
votes
1answer
145 views

How is impedance matching related to balance and common-mode currents?

Does a good impedance match imply good balance and lack of common-mode currents? Does a poor impedance match imply poor balance and excessive common-mode currenst?
9
votes
2answers
1k views

Why is the risk of damage to a transmitter due to a mismatched antenna at lower frequencies greater?

A quick follow-up to this answer ... If the impedance mismatch is large, you risk damaging your radio, particularly on the lower frequencies ... I'm sorry to be so dense, but uh why is the risk ...
2
votes
1answer
311 views

What is this matching technique called?

I've had this suggested to match 50 ohm coax to a lower feedpoint impedance, like a vertical, especially mobile shortened verticals. What's it called? simulate this circuit – Schematic created ...
10
votes
1answer
2k views

How to combine two 50 Ω antennas such that they appear as one 50 Ω load?

I'm looking for a simple way to impedance match an array of two 50 Ω antennas so that when they are combined they appear as one 50 Ω load. Assume that both antennas are identically constructed, are ...
18
votes
3answers
8k views

Why do I need to tune an antenna?

I've heard that when an antenna is set up, it needs to be tuned to reduce reflective power back into the radio. Is this always necessary, and if so how would I go about tuning it?

1
2