Questions tagged [impedance-matching]

Questions about fixed impedance matching networks, the necessity of impedance matching, etc.

Filter by
Sorted by
Tagged with
3
votes
1answer
426 views

Understanding of NFC Reader Antenna matching

I have been designing a 20 x 20 cm square NFC reader antenna which looks like this: In order to make it work and detect NFC tags at certain distance, it needs to be matched. To do that I was trying ...
0
votes
1answer
212 views

NFC coil matching - Q factor improvement

I have been trying to match my NFC reader coil of size 20*20 cm with a three element circuit - one capacitor in series, another in parallel and one resistor in parallel. I have been using Texas ...
1
vote
2answers
115 views

Removing the whip on a 2m/70cm antenna makes no difference

Today I was trying to measure the SWR of a new aerial on my car which has 3 loading coils. Whilst doing this I took the whip out on the top to see how drastically I might have needed to cut the ...
3
votes
1answer
180 views

How high an SWR can the USRP 2901 (B210) handle?

I connected a USRP 2901 (B210) to an amplifier I designed. The USRP seems to shutdown every time I try to transmit. I guess I messed up with the input impedance matching on the amplifier. Is it the ...
4
votes
5answers
386 views

Coax cable as antenna for 5 watt handy

For a normal 5 watt handy working in VHF or UHF freq with 50 ohm antenna , is it possible to use a same length coax cable instead of a stub antenna, so as to work like a crude antenna. Will this only ...
2
votes
1answer
91 views

Inductors for Impedance Matching

I need to impedance match an IF mixer circuit to a 10.7MHz crystal filter. One of the inductors was calculated to be 44 $\mu$H. So I need a relatively large value inductance in a small package to fit ...
5
votes
2answers
2k views

How can the design of an RF filter also encompass impedance matching?

I'm installing an antenna which will require a matching network. (A fixed network: the load will not change.) I'm also building some low-pass filters to reduce transmitted harmonics. It would be a ...
3
votes
3answers
1k views

What is the output impedance of a typical solid state ham transmitter?

I've often heard that the output impedance is 50Ω, and the load impedance should be matched to that and also 50Ω. While the reasons for the load impedance to be 50Ω are clear, is the output impedance ...
1
vote
1answer
269 views

Intermittent High SWR

Using a Cushcraft MA5B beam, when I apply high power from an amplifier, the SWR will go up and down intermittently. Something is breaking down at high power (200-500 W). I have a new coax feedline, ...
8
votes
1answer
308 views

SWR Measured at the Transmitter versus SWR at the Antenna

It is fairly well understood that due to transmission line losses, the SWR as measured at the transmitter will be less than the SWR at the antenna. Some of the new antenna analyzers and some vector ...
9
votes
1answer
223 views

Does Coax Limit the Maximum SWR a Transmitter 'Sees'?

A recent discussion about SWR led to the assertion that a length of coax cable will ultimately limit the SWR to which the transmitter will be exposed. By experimenting with an SWR calculation tool ...
2
votes
3answers
959 views

How do I set up my radio for an antenna tuner?

I recently acquired an MFJ Versa Tuner II model MFJ-949D as well as a Kenwood TS-430S radio. The instructions for the tuner state (in part): For optimum operation of the MFJ-949D, the transmitter ...
2
votes
1answer
173 views

Dual Band Antenna Matching

I am building a wideband dual band omni for school. My antenna is about 2m long. The antenna length basically has two sections (divided by ports) - from 0 - 1.8m (This length is for 20-180MHz) and ...
3
votes
1answer
1k views

Is ladder line necessary when using a non-resonant dipole through a tuner?

I've heard if I have a dipole of some arbitrary length, or a random wire, the SWR can be very bad. An antenna tuner can present a decent match to the transmitter, but the SWR on the feedline will be ...
2
votes
2answers
137 views

Antenna experimentation

I want to make a DIY antenna for my Kenwood TH-F6A. Is there any danger of damaging the radio (i.e. by trying an antenna that is unsuitable), or is it safe to experiment?
2
votes
1answer
313 views

What is this matching technique called?

I've had this suggested to match 50 ohm coax to a lower feedpoint impedance, like a vertical, especially mobile shortened verticals. What's it called? simulate this circuit – Schematic created ...
10
votes
1answer
2k views

How to combine two 50 Ω antennas such that they appear as one 50 Ω load?

I'm looking for a simple way to impedance match an array of two 50 Ω antennas so that when they are combined they appear as one 50 Ω load. Assume that both antennas are identically constructed, are ...
18
votes
3answers
8k views

Why do I need to tune an antenna?

I've heard that when an antenna is set up, it needs to be tuned to reduce reflective power back into the radio. Is this always necessary, and if so how would I go about tuning it?
2
votes
1answer
149 views

How is impedance matching related to balance and common-mode currents?

Does a good impedance match imply good balance and lack of common-mode currents? Does a poor impedance match imply poor balance and excessive common-mode currenst?
2
votes
2answers
1k views

3 way coax split / impedance match

I would like to split a coaxial feed line 3 ways, maintaining 50 Ω impedance. I know how to do this 2 ways; you use 1/4 wavelength 75 Ω coax as matching stubs. I know how to do this 4 ways; you do 2 ...
2
votes
3answers
220 views

Do stub matching techniques still produce some loss?

I am using a double stacked Yagi-Uda antenna with about 57 Ω impedance. The 50 Ω feed line (coaxial) cables are combined using a tee connector. I observed, at the output of the tee connector, an ...
9
votes
2answers
1k views

Why is the risk of damage to a transmitter due to a mismatched antenna at lower frequencies greater?

A quick follow-up to this answer ... If the impedance mismatch is large, you risk damaging your radio, particularly on the lower frequencies ... I'm sorry to be so dense, but uh why is the risk ...
4
votes
1answer
267 views

What kind of losses do you get from an LC network matching the antenna's impedance?

If you have a transmitter that is perfectly on your frequency but you have an antenna with some impedance what types of losses, and of what magnitude, will you expect from a tuner in between your ...

1
2