Questions tagged [impedance-matching]

Questions about fixed impedance matching networks, the necessity of impedance matching, etc.

Filter by
Sorted by
Tagged with
18
votes
3answers
8k views

Why do I need to tune an antenna?

I've heard that when an antenna is set up, it needs to be tuned to reduce reflective power back into the radio. Is this always necessary, and if so how would I go about tuning it?
10
votes
5answers
844 views

How did hams manage to tune their antennas before VSWR meters?

In the early 20th century --back when the hobby was still new-- before VSWR meters and antenna analyzers were invented, how did radio operators know whether they were tuned for maximum power out? ...
2
votes
1answer
146 views

How is impedance matching related to balance and common-mode currents?

Does a good impedance match imply good balance and lack of common-mode currents? Does a poor impedance match imply poor balance and excessive common-mode currenst?
9
votes
1answer
220 views

Does Coax Limit the Maximum SWR a Transmitter 'Sees'?

A recent discussion about SWR led to the assertion that a length of coax cable will ultimately limit the SWR to which the transmitter will be exposed. By experimenting with an SWR calculation tool ...
8
votes
3answers
831 views

RigExpert AA-35 - Interpreting The Information

I have a new RigExpert AA-35 antenna analyzer. 1st one I have had & 1st time trying to use an analyzer on an antenna. My questions are very basic and general, but I am having difficulty in ...
10
votes
1answer
2k views

How to combine two 50 Ω antennas such that they appear as one 50 Ω load?

I'm looking for a simple way to impedance match an array of two 50 Ω antennas so that when they are combined they appear as one 50 Ω load. Assume that both antennas are identically constructed, are ...
9
votes
2answers
1k views

Why is the risk of damage to a transmitter due to a mismatched antenna at lower frequencies greater?

A quick follow-up to this answer ... If the impedance mismatch is large, you risk damaging your radio, particularly on the lower frequencies ... I'm sorry to be so dense, but uh why is the risk ...
8
votes
1answer
299 views

SWR Measured at the Transmitter versus SWR at the Antenna

It is fairly well understood that due to transmission line losses, the SWR as measured at the transmitter will be less than the SWR at the antenna. Some of the new antenna analyzers and some vector ...
3
votes
1answer
1k views

Is ladder line necessary when using a non-resonant dipole through a tuner?

I've heard if I have a dipole of some arbitrary length, or a random wire, the SWR can be very bad. An antenna tuner can present a decent match to the transmitter, but the SWR on the feedline will be ...
3
votes
1answer
418 views

Understanding of NFC Reader Antenna matching

I have been designing a 20 x 20 cm square NFC reader antenna which looks like this: In order to make it work and detect NFC tags at certain distance, it needs to be matched. To do that I was trying ...
2
votes
2answers
1k views

3 way coax split / impedance match

I would like to split a coaxial feed line 3 ways, maintaining 50 Ω impedance. I know how to do this 2 ways; you use 1/4 wavelength 75 Ω coax as matching stubs. I know how to do this 4 ways; you do 2 ...
1
vote
2answers
593 views

Exactly why do some SWR meters give a changing reading depending on the length of coax used to connect to an antenna?

Following is my understanding of some theory and the questions are at the end. Is this right ? ... A standing wave is an AC waveform oscillating at a particular frequency which has a varying ...
0
votes
2answers
631 views

Understanding RG6-75 ohm Cable Impedance

Here is my measurement to a piece of RG6 cable. It is around 30cm cable. On the shield is written COAXIAL CABLE 5C-2V 75 ohm. From my measurement I got data as below: From that table, we can see that ...