Skip to main content

Questions tagged [icom]

An International manufacturer of radio equipment, Based in Japan. Their products include equipment for radio amateurs, pilots, maritime applications, land mobile professional applications and scanning enthusiasts.

11 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3 votes
1 answer
176 views

Linking DStar repeaters using Icom syntax

I would like to monitor a remote repeater (VE2RM) through my local repeater (VE3TTT). I am trying to figure out how to link them - specifically using the Icom ID-52A commands/syntax. I found some ...
TSG's user avatar
  • 259
2 votes
0 answers
505 views

wsjt-x problems with windows 11 Icom 7300 USB sound hangs

Description of problem: WSJT and JTDX both stop receiving sound after about 2-3 hours when running on Win 11 with ICom 7300. This did not happen with my Raspberry Pi running the same rig. The ...
Peter Burke's user avatar
2 votes
0 answers
464 views

What could cause an Icom IC-756 Pro II to suddenly stop transmitting?

My HF radio (Icom IC-756 Pro II) suddenly won't receive or transmit. I recorded the sound it makes when receiving and uploaded it to https://w7bkg.org/wiki/File:Radio_Issue.wav . It sounds the same on ...
kj7rrv's user avatar
  • 179
2 votes
0 answers
167 views

Diagnosing IC-7100 Drive Amp Bias | PA Won't TX

A faulty in vehicle DCDC charger has fed 16V or so into my brand new IC7100, killing the main board and preventing it from transmitting. I've replaced the mainboard with a brand new one however I'm ...
Alex Turner's user avatar
1 vote
0 answers
96 views

Why does Ham Radio Deluxe stops working when I change the AGC setting on my Icom IC-705 radio?

When I start rig control on Ham Radio Deluxe it works as long as AGC in my Icom IC-705 is in medium and I don't change it. If it's in slow it manages to read the frequency, but then it gets stuck. If ...
Pablo Fernandez's user avatar
1 vote
1 answer
299 views

Icom RS-MS3W setup

I am trying to use terminal mode for the first time on my Icom ID-52A. I am already registered on DStar (through the UTRUST/national site, not a specific repeater). I am trying to understand what ...
TSG's user avatar
  • 259
1 vote
1 answer
303 views

FLDigi Crashes When Trying to Load RigCAT Description File

I am trying to setup FLDigi with my ICOM-7300 via the USB connection so I can start using digital modes. Everytime I try to follow the instructions here, it doesn't work. Specifically, everytime I try ...
SandPiper's user avatar
  • 777
1 vote
0 answers
80 views

Receiving BFSK with 9.6 khz deviation on TS-2000 / ICOM(IC-910H) in FM mode

I have used Kenwood TS-2000 to receive BFSK signals with 3.3 khz deviation operating the TS-2000 in FM mode. Can we receive similar signals but whose BFSK deviation is 9.6 Khz using either the TS-2000 ...
Ashish kulkarni's user avatar
0 votes
0 answers
54 views

ICOM R8500-Transfer data and audio through e-line services

I have tree icom R8500 radio receivers and i want to upgrade my services from serial to Ethernet. Although i have successfully managed to transfer data from the receivers to my pc (which happens to be ...
0 votes
0 answers
174 views

I'm trying to configure HRD for IC7300 but cannot connect / detect frequency

Got the firmware updated. Got the Driver updated. Got the software updated. Went through instructions several times.
NonYaBidnezz's user avatar
0 votes
0 answers
261 views

Troubleshooting ICOM PS15 Power Supply

I got a power-supply gifted by my friend. When I powered ON, the main (120V) FUSE blows up. I started by disconnecting the transformer from the control circuit and powered ON. This time the fuse is ...
Raajkumar's user avatar
  • 109