Questions tagged [ferrite]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
7
votes
2answers
197 views

Importance of Ferrite Size in Coax Choke Balun

The question is quite simple: When making a coax choke balun, does the size of the ferrite matter, and if so, why? I have seen design notes that say to use a single FT240-43 toroid for powers up to ...
3
votes
1answer
80 views

How does this 3 dB splitter/combiner work?

I'm having difficulties to understand how does this circuit work: Apparently T1 is a regular 50 Ohm to 22.2 Ohm autotransformer. Turns ratio 2:3 gives a 0.66**2 impedance converation. Since the load ...
3
votes
0answers
120 views

9:1 unun material and power loss

I need to build another 9:1 unun and I start searching for my toroids... (I have build 2-3 something like 4 years ago)... In parallel I checked on Google about the correct toroid etc so I found 2-3 ...
4
votes
1answer
114 views

Commercial Loopstick Antenna Manufacturers?

I am an electrical engineer working on a product that needs a loopstick antenna. I had thought that AM radios were so commoditized that I'd be able to find an off-the-shelf vendor. However the closest ...
5
votes
0answers
81 views

What causes differences in properties of ferrite cores from same material?

Why are the shapes of the impedance curves different for cores made of the same ferrite material? The impedance (Z) of an inductor wound on a ferrimagnetic core is: $$Z=j\omega L_s + R_s = j\omega ...
0
votes
0answers
28 views

UHF cubical quad VNA analysis interpretation (part2)

This is the follow up to: UHF cubical quad VNA analysis interpretation This is a S21 and S31 analysis of an oversized 385 Mhz 50 Ohm to 90 Ohm balun between 100 Mhz and 600 Mhz I tested phase ...
5
votes
1answer
256 views

How do I evaluate and use a toroidial core for my HF double-balanced mixer?

Last year, I planned to make a double-balanced mixer covering the entire 3-30 MHz band as an upconverter for my RTL-SDR receiver, mainly for learning RF circuits and ham radio. Naturally, it requires ...
6
votes
1answer
516 views

How to measuring ferrite core efficiency vs frequency

There is an unknown ferrite toroid. I would like to figure out whether it can be used in an audio transformer, or maybe in a 1:4 transformer on given HF frequency. The experiment I came up with is ...
5
votes
2answers
114 views

Can ferrite beads lower coax cable velocity factor?

For VHF and UHF, it seems reasonable to slip ferrite beads over a coaxial cable to act as a transmission line common mode choke. It also seems reasonable to use beads with the smallest diameter ...
0
votes
1answer
146 views

Can I make ferrite paint? Will it shield my antenna from my roof?

I have a 3 element vertical Yagi mounted on a rotator, and in one direction the roof of the house gets pretty close and messes up the SWR a bit. If i mash up a few type 43 material ferrite cores and ...
7
votes
1answer
391 views

How to make a ferrite bar antenna for RTL-SDR?

I bought a RTL-SDR (blue one with little MCX antenna). I modified its Q branch, and can receive short wave radio with Degen 31MS antenna now. For MW, Degen 31MS antenna has a ferrite bar antenna ...
5
votes
3answers
837 views

Is this the Correct Ferrite Core to Reduce RFI as a Common Mode Choke?

I have a Flex 3000 connected via RG-11 coax to a inverted V fan dipole tuned for 40m and 20m on my roof. I have an "ugly" balun up on the mast by the antenna. I further have the feed-line going into a ...
7
votes
2answers
725 views

What is the maximum number of turns in a ferrite core used as a common mode choke?

Is there a way to estimate the maximum number of turns which can be used with a ferrite core used as a common mode choke? It is known that the impedance of such a choke is proportional to the square ...
1
vote
1answer
157 views

Need a ferrite suppression material for choking 15 kHz to 60 kHz

Electric fence RFI is ruining reception on our VLF lightning receivers, and we need a material to place around neighbors' fence wires to suppress the noise being radiated. Preferably, a split bead, ...
2
votes
2answers
670 views

What core material do I need to construct a 1:1 unun for 6M?

I want to build a 1:1 unun for a 6M dipole. Power level 100W. What core material should I use?
6
votes
2answers
486 views

Ferrite rod permeability determination

Is there a simple empiric way of determining the permeability (mhu) of a ferrite object (be it a ring, rod or any form)? I've been thinking this for a rod: if I wind coils with different number of ...
6
votes
1answer
200 views

Are some ferrites porous enough they should be protected outside?

I recently bought a couple of 61-mix toroids, and as usual I wrote the mix number on them before they become mystery parts. However, the ink soaked right into the ferrite. I've left ferrites hanging ...
1
vote
1answer
889 views

Do a toroid's specs matter much in an antenna matching transformer?

I'm getting started with my first (very basic) HF rig and for convenience and the experience I'd like to try an End Fed Half Wave antenna. Typical designs for a "matchbox" in this case include ...
2
votes
1answer
141 views

Ferrite Rod Price Differences

We are trying to make a VLF geophysics device for our graduate project and we need two ferrite rod antennas (desired length is 6"). Searching on the internet, we have found two ferrite rod suppliers. ...
13
votes
2answers
3k views

How does one read a ferrite datasheet?

Datasheets for ferrite materials are usually filled with incomprehensible graphs with greek letters. For example, Fair-Rite's 73 material: What's a $\mu'_s$ and a $\mu''_s$? What do these numbers ...
8
votes
1answer
3k views

What's an appropriate core material for a loopstick antenna?

A loopstick antenna, if you don't know, is a coil of many turns around a high permeability core. They are frequently encountered in AM receivers and look like this: This particular example is ...