Questions tagged [electronics]

Questions which involve the properties or applications of individual electronic components.

Filter by
Sorted by
Tagged with
5
votes
0answers
77 views

How to estimate input and output impedance of an amplifier?

I'm trying to figure out how to design power amplifiers which input and output are properly matched to 50 Ohm. My thinking was that the most bullet proofed approach would be to model an amplifier in ...
1
vote
4answers
144 views

Can't identify old Chinese(?) and American radio/telephone

I have searched image banks and Googled period radios, but I can not identify these old units. I picked them up overseas in SE Asia and I got them as projects to teach myself enough to challenge the ...
1
vote
5answers
267 views

Significance of 1/4 wavelength with respect to antennas

I am a fresher in the radio design field. My question is, 'What is so significant about 1/4 wavelength with respect to antennas.' From the information I have gathered from various sources, it is my ...
4
votes
1answer
167 views

Identification of valve

My favorite receiver used for 40 m AM broadcasts has a cracked valve, but the valve type normally printed on the glass has rubbed away. Can anyone tell me what the numbers for this valve are ? The ...
0
votes
1answer
118 views

Where am i supposed to ground the audio path?

Where does the ground of the audio path go in this schematic?
2
votes
0answers
36 views

Clocking A and N in a Dual-modulus PLL Prescaler

In an effort to "up my game" attempting to build a VFO for my DIY transceiver, I've been looking at PLL theory and circuits. Many of my research references are quite old and I understand that many of ...
3
votes
1answer
63 views

How can i adjust the IF strip in a single conversion SSB receiver which has a product detector?

I have an analog 27 MHz transceiver which i am planning to convert to 10 m. The radio is an AM / SSB unit with a single conversion superhet receiver with an IF of 7.8 MHz using a crystal filter. This ...
2
votes
0answers
98 views

Unknown kit from DK0TV

When my father - who became a ham years after I did - passed away, I found an unstarted project (board + components), which I only re-discovered again years later. The board is marked DK0TV-001, and ...
3
votes
1answer
71 views

What is unique about a Low Noise Amplifier (LNA)?

What is so special about a low noise amplifier? If I were to design an amplifier, I would always design an amplifier with low noise anyway. Why is it emphasised as being “Low Noise”? What are the ...
0
votes
1answer
98 views

What does “HF-QUARTZ 4.19 MHz” on a ~1980s wall clock mean?

I have a wall clock from the 1980s or early 1990s. Probably 1980s. It has a black box behind/"inside" it which powers the whole thing. It's made by Quartz. On the black box, it says "HF-QUARTZ 4.19 ...
0
votes
0answers
36 views

Which specification is exceeded for a transistor output stage in a transmitter when there is a high SWR? [duplicate]

For a transmitter which has an output stage which uses one final output power transistor, when the SWR is high, it's common knowledge it seems that the output transistor can get hot and fail due to ...
2
votes
1answer
68 views

voltage rating for RF filter components

I want to design a PCB for a diplexer for Satellite operations. I want to use SMD capacitors and possible inductors to get some experience with soldering SMD components. What should the voltage rating ...
0
votes
1answer
47 views

Had +5VDC and GND swapped, feeding a GPS receiver. Source is +5VDC output @ DB9 port on Yaesu FT-2600M, now showing 0V. Did I fry something?

Basically, I connected +5VDC to the ground of a GPS receiver, and now have no power from the power source. Is it possible to mess something up by doing this? I feel like this is more of a basic ...
0
votes
1answer
77 views

Can i use an anaolgue IC switch to change a 10 m yagi's directivity by somehow combining received signals with different variable phase?

Can i use an analogue IC switch being triggered at the same frequency I am receiving on to change a 10 m yagi's directivity by somehow combining received signals with different variable phase either ...
5
votes
3answers
222 views

ARRL handbook as a reference for all your radio learning needs?

Looking to take up learning understanding everything from basic electronics to how today's wideband radios work, so that I can build my own radio systems (not just ham radios), and talk radio concepts ...
1
vote
2answers
75 views

How is frequency selection (tuning) accomplished in a direct conversion receiver?

How is frequency selection (tuning) accomplished in a direct conversion receiver ? A crystal filter can't be used is that correct ? Because there is no IF to mix with the incoming frequency band ...
3
votes
2answers
121 views

What are the advantages for a receiver that uses an IF compared to direct conversion?

What are the advantages for a receiver that uses an IF compared to direct conversion ?
1
vote
2answers
109 views

If I parallel two crystal filters together, will that double the bandwidth? [closed]

Will the bandwidth be doubled ? And will the impedance be halved ?
4
votes
2answers
142 views

Dipole increased CM current using choke balun

My 20 meter inverted vee dipole is fed with 56 feet of 50-ohm coax. The SWR measures 1.2 at the center of the band. According to http://arrl.org/grounding a balanced antenna doesn't need a ground, so ...
1
vote
3answers
234 views

How does the Maximum Power Transfer Theorem relate to RF power amplifiers?

The Maximum Power Transfer Theorem says that maximum power transfer occurs when the source impedance equals the load impedance, when the power transferred to the load is 50%, the other 50% being ...
4
votes
4answers
289 views

Why does an RF Amplifier fail when the SWR is high?

Exactly why does an RF output transistor fail if the SWR is bad ? Is it A because the impedance mismatch between the transmission line and the antenna results in maximum power not being transferred ...
2
votes
3answers
1k views

Voltage vs. Current Balun for Dipole

I'm a new radio amateur setting up a half-wave 10-meter inverted vee antenna fed by 50 ohm coax. I understand that the inverted vee lowers the normal 72 ohm dipole closer to 50 ohms, so I only need to ...
3
votes
4answers
160 views

How is working on DC high voltages as in a tube radio different from 120VAC?

Suppose that I am familiar with the safety procedures for working on 20 A 120 VAC 60 Hz household lines. What should I be prepared for before working on high voltage DC circuits (say, 800 volts) as ...
4
votes
1answer
114 views

Is it practical to use a magnetic amplifier as an AM modulator in a transmitter?

If I'm building a vacuum tube HF transmitter (say, 40 m band), obviously the simplest mode to build is CW; it's common to key the oscillator input to the final (in order to keep the oscillator running ...
1
vote
0answers
60 views

Are jammers relate to electronics or electrotechnics , why? [closed]

Are jammers relate to electronics or electrotechnics , why ? Please ,tell me the main difference between electronics and electrotechins and why we can classify jammers as electrotechics or ...
7
votes
1answer
379 views

Double power-handling ability of RF amplifier output transformer

I want to base the output network for a 500W push-pull HF amplifier on "A 250W Broadband Linear Amplifier" described in Chapter 17 of the 2014 ARRL Handbook. I need advice on whether and/or how the 1:...
6
votes
7answers
658 views

Is it practical to use a slug-tuned variable inductor in an antenna matcher (aka “antenna tuner”)?

I will soon need an antenna impedance match (aka "antenna tuner"), because I'll initially only have a single antenna for my HF rig (needs to cover 80m, 40m, 20m, 15m, and 10m). Obviously, in order to ...
1
vote
1answer
107 views

How can the output power of a Yaesu FT101E be increased?

I have a Yaesu FT101E which has low output because the final 6JS6C valves are old. If i increase the plate voltage on the final tubes from 600 to 800 VDC by changing the mains transformer tapping ...
2
votes
3answers
157 views

Is double amplitude modulation useful?

If i amplitude modulate an AM carrier with an audio signal, can i then feed that resultant AM waveform into another modulator and amplitude modulate the AM signal to give a signal which is amplitude ...
2
votes
1answer
68 views

Attenuator Cascaded Connection

PAT1220-C-10DB-T5 is a 10dB attenuator. (This chip is just an example, it could be any other component as well). Can I simply connect 3 of them in series in a PCB design to make my cheap 30dB ...
1
vote
3answers
569 views

How to reduce voltage ripple of a linear power supply?

I made a simple linear power supply for my transceiver using 12V 30A transformer, four diodes RHRP3060 forming a rectifier and three 30_000 µF capacitors connected in parallel. I also used a 200 Ω 50W ...
2
votes
1answer
72 views

Can an indoor antenna damage unshielded electronics?

I have a 25w radio running through a ~4.5db gain antenna. If I use a 4W HT indoors, I can hear a loud buzzing noise emmanating from my computer speakers. If I used the 25w mobile with the 4.5db gain ...
-1
votes
1answer
55 views

Skin effect for a modified antenna with a high frequency pulsed DC

A direct current will be interrupted by a high frequency switch. It seems , that in a wire, connected to the source (the antenna rod), instead of pushed back- and forwards electrons, the electrons get ...
5
votes
2answers
346 views

Share wide band antenna with multiple transceivers

I'm trying to incorporate several transceivers on my board design; I need WiFi (2.4 GHz) SatCom (~1.6 GHz) RF (~900 MHz) and GNSS (~1.5 GHz). I need to combine them into one antenna. I found a wide ...
7
votes
2answers
210 views

Water cooling a GS-35B in lieu of air cooling?

Does anyone know how to --or have any experience with-- water or oil-cooling the anode? Since forced-air cooling is required, the sound from the blower and the exhaust air would be too noisy for my ...
7
votes
1answer
2k views

How to determine number of turns for a 1:1 balun?

I would like to make a 1:1 balun with М1000НМ ferrite core (magnetic permeability - 1000) and 1 mm thick copper wire using triple bifilar winding. Unfortunately I didn't manage to find a clear ...
2
votes
2answers
742 views

Why does a Class-C non-linear power amp distort SSB but does not distort AM?

Can someone tell me why exactly a transistor non-linear power amplifier will amplify an AM signal without noticeable distortion, but will distort an SSB signal, giving the familiar scratchy sound ...
6
votes
2answers
755 views

Feed-through Capacitors

I'm in the "information gathering" phase of a RF Power Meter project and the design I fancy (W7ZOI Power Meter) calls for a feed-through capacitor at the output port. I understand that a feed-through ...
5
votes
2answers
389 views

Is there a best ratio of L to C in a resonant circuit?

When designing a resonant circuit, for example as a local oscillator, the product of $L$ and $C$ determine the resonant frequency according to $$f_{res} = \frac{1}{2\pi \sqrt{L C}}.$$ This means that ...
0
votes
1answer
237 views

ADS Simulation: How to model an antenna in a simple rectifier circuit?

As titled, I'd like to explore the output power of a simple diode-based rectifier circuit, excited by an antenna (assumed to be 50 ohm impedance). Please give me some advice as to how to do this. It ...
9
votes
0answers
164 views

UHF FM power amplifier design without expensive software

I'm designing a small UHF data transceiver for the 70cm band, based on a Silicon Labs EZRadioPro Si4463 IC. Modulation is FM, 12.5kHz channel step. The concept is similar to SiLabs' AN656 application ...
6
votes
0answers
206 views

Beyond Maximum Stable Gain of a transistor

I was plotting constant-gain circles on the Smith chart the other day for a potentially unstable RF transistor. I recently read on-line that for a potentially unstable transistor the maximum gain ...
7
votes
2answers
367 views

Learning RF electronics

I've been studying and building test circuit for actually several YEARS now, so far with no success. It sounds ridiculous but it's true. So I feel like I have a good understanding or RLC circuits, I ...
0
votes
1answer
60 views

Reflection Coefficient to Impedance transformation on the Smith Chart

A certain RF transistor has a source - reflection coefficient with a magnitude of .105 and a phase angle of 160°. When plotted on the Smith Chart, the normalized impedance is .825 +j .06 Ω. What is ...
1
vote
3answers
118 views

I just got this RF equipment but i don't know what's for

I got some RF equipment for free (it was going to the trash and I 'rescued' it). It's almost new, and seems expensive, but i don't know it's purpose. Googling the model numbers yields very little ...
2
votes
2answers
581 views

What's the difference between a Return Loss Bridge and a Circulator?

From my understanding a return loss bridge basically consists of three terminals: an RF input, a DUT output and a RF output which goes to say a spectrum analyzer; I understand that the RF input signal ...
3
votes
1answer
244 views

Series resonant circuit, how to calculate voltage across the capacitor?

This is question a3i3-1 from the practice questions in the book "amateur radio Exam Secrets": A series resonant circuit has 10V peak across it when at resonance. At that frequency the resistance of ...
4
votes
4answers
3k views

What are some equivalents of a BF199 transistor?

I'm planning to build an FM radio receiver using the instructions on http://www.instructables.com/id/Build-your-own-Crude-FM-Radio/ The schematic uses a BF199 transistor which is marked "obsolete" by ...
2
votes
1answer
84 views

Inductors for Impedance Matching

I need to impedance match an IF mixer circuit to a 10.7MHz crystal filter. One of the inductors was calculated to be 44 $\mu$H. So I need a relatively large value inductance in a small package to fit ...
5
votes
2answers
306 views

What is Norton's transform?

This article from Itchen Valley Amateur Radio Club describes an interesting technique called "Norton's transform": This results in a negative capacitor, but in a circuit where there are other ...