Questions tagged [electronics]

Questions which involve the properties or applications of individual electronic components.

Filter by
Sorted by
Tagged with
10
votes
3answers
3k views

Why does “high SWR” damage transmitters, instead of “impedance mismatch”?

In the audio realm, where cable lengths are insignificant compared to the signal wavelength, I would understand an impedance mismatch damaging an amplifier as follows: Take an audio amplifier that ...
5
votes
2answers
1k views

Adapting an antenna coupler

I've built AA5TB's antenna coupler: I left out C2 because I didn't understand why I would need it - why would I? It works fine without. Unfortunately, when I started tuning for a 5W 20m transceiver, ...
18
votes
3answers
4k views

SDR sampling bandwidth - do the bits per sample matter?

I'm looking at data converter chips for a homebrew SDR design, and I see that I can choose not just the sampling frequency, but also the bits per sample. Obviously the sampling frequency has to be ...
7
votes
1answer
2k views

How to determine number of turns for a 1:1 balun?

I would like to make a 1:1 balun with М1000НМ ferrite core (magnetic permeability - 1000) and 1 mm thick copper wire using triple bifilar winding. Unfortunately I didn't manage to find a clear ...
5
votes
2answers
2k views

How to find or derive the maximum safe input power to a receiver?

A number of my RF devices have a specified safe maximum input power, for example: "The maximum RX power of HackRF One is -5 dBm. Exceeding -5 dBm can result in permanent damage!" source "If you look ...
10
votes
1answer
3k views

How does a switching mixer multiply the two signals?

I understand what a mixer does, and when I see it in a block diagram it's obvious what purpose it serves and how it fits in the overall design of the radio. However, when I look at the schematics and ...
6
votes
3answers
4k views

How should this SWR meter's directional coupler work?

I'm wrapping up a "home build" of the MFJ-941EK antenna tuner kit and having trouble getting the wattmeter calibrated. I can't use C4 to get the reflected power reading calibrated down to 0 as is ...
6
votes
7answers
735 views

Is it practical to use a slug-tuned variable inductor in an antenna matcher (aka “antenna tuner”)?

I will soon need an antenna impedance match (aka "antenna tuner"), because I'll initially only have a single antenna for my HF rig (needs to cover 80m, 40m, 20m, 15m, and 10m). Obviously, in order to ...
4
votes
4answers
342 views

Why does an RF Amplifier fail when the SWR is high?

Exactly why does an RF output transistor fail if the SWR is bad ? Is it A because the impedance mismatch between the transmission line and the antenna results in maximum power not being transferred ...
3
votes
1answer
195 views

Would a switched RF attenuator be (a)symmetric?

I picked up this 0-80 dB switched RF attenuator at a flea market, with no part number or other useful markings other than the knob settings. I've tested it and confirmed that it works, but there's one ...
3
votes
1answer
269 views

Series resonant circuit, how to calculate voltage across the capacitor?

This is question a3i3-1 from the practice questions in the book "amateur radio Exam Secrets": A series resonant circuit has 10V peak across it when at resonance. At that frequency the resistance of ...
2
votes
3answers
2k views

Voltage vs. Current Balun for Dipole

I'm a new radio amateur setting up a half-wave 10-meter inverted vee antenna fed by 50 ohm coax. I understand that the inverted vee lowers the normal 72 ohm dipole closer to 50 ohms, so I only need to ...
2
votes
1answer
685 views

Adding a panadapter via SDR

I've become very accustomed to the waterfall display on my SDR, especially for digital modes over HF. I'm thinking about tying into the IF on my IC-718 and connecting to an SDR to add a waterfall to ...
2
votes
2answers
456 views

Adapting an antenna tuner for use with a panel meter instead of an LED

I'm building NorCal's / W6JJZ's BLT tuner (pdf) for use on 40m/20m with a 5W transmitter. I would like to remove the LED and use a small panel meter instead. I don't have a 1N34A at hand, but I do ...
2
votes
5answers
327 views

Significance of 1/4 wavelength with respect to antennas

I am a new to the radio design field. My question is, 'What is so significant about 1/4 wavelength with respect to antennas.' From the information I have gathered from various sources, it is my ...
2
votes
3answers
159 views

Is double amplitude modulation useful?

If i amplitude modulate an AM carrier with an audio signal, can i then feed that resultant AM waveform into another modulator and amplitude modulate the AM signal to give a signal which is amplitude ...