The Stack Overflow podcast is back! Listen to an interview with our new CEO.

Questions tagged [balun]

Devices for connecting balanced and unbalanced feed lines/antennas. Also covers questions about ununs, unbalanced-to-unbalanced connection.

Filter by
Sorted by
Tagged with
0
votes
0answers
24 views

UHF cubical quad VNA analysis interpretation (part2)

This is the follow up to: UHF cubical quad VNA analysis interpretation This is a S21 and S31 analysis of an oversized 385 Mhz 50 Ohm to 90 Ohm balun between 100 Mhz and 600 Mhz I tested phase ...
1
vote
1answer
52 views

Rotatable Dipole & RF Choke

I have a Diamond HFV-5 (rotatable dipole) in the attic fed by ~30ft of coax. The antenna system comes with a Balun at the feedpoint. Would it be worthwhile to add an inline RF Choke (Unun) in addition ...
5
votes
5answers
114 views

How to match low impedance of NVIS Dipole?

I want to match a 50-ohm coax feed wire to a 40-meter NVIS half-wave dipole. NVIS antenna examples I've found are usually based on a regular dipole (72 ohms in free air). However the impedance drops ...
2
votes
2answers
104 views

Will using a 1:1 balun at the feedpoint of a center feed dipole result in no common mode current on the outside of the coax?

Will using a 1:1 balun at the feedpoint of a center-fed dipole when using coax result in no common mode current on the outside of the coax ?
3
votes
1answer
52 views

UHF cubical quad VNA analysis interpretation

I've designed a two element UHF cubical quad. It was designed to resonate at 385 Mhz. I used 0.1mm thick and 1cm wide copper tape instead of wire to lower the antenna Q. I used PVC electrical conduit ...
4
votes
2answers
84 views

Dipole increased CM current using choke balun

My 20 meter inverted vee dipole is fed with 56 feet of 50-ohm coax. The SWR measures 1.2 at the center of the band. According to http://arrl.org/grounding a balanced antenna doesn't need a ground, so ...
3
votes
1answer
81 views

How does a 1:4 current balun work?

I'm having little difficulties understanding the following schematic: I understand the part regarding current distribution. I understand why this schematic suppresses common mode current. Also I ...
1
vote
3answers
128 views

How to calculate impedance in antenna design's practice?

I would like to make a match half wave length (λ) dipole antenna (or probably a short dipole antenna). So I would like to make it by measure using LCR meter. What I am still confuse is about what is ...
2
votes
2answers
173 views

Voltage vs. Current Balun for Dipole

I'm a new radio amateur setting up a half-wave 10-meter inverted vee antenna fed by 50 ohm coax. I understand that the inverted vee lowers the normal 72 ohm dipole closer to 50 ohms, so I only need to ...
1
vote
0answers
46 views

advice needed for balanced line terminals

I am designing a portable antenna with a radiating element and a balun that are not close to each other. The impedance has been designed to be close to 50 ohms. ...
3
votes
2answers
213 views

Can I use a 1:1 current balun to feed a 1/4λ vertical?

I have an LDG RBA-1:1 current balun, and I was wondering if it behaves as a common-mode choke that I can use for a ground-mounted quarter wave vertical w/ 16 radials. The other choice I have is a 4:...
3
votes
2answers
85 views

Tips for HF Antenna with house near AM transmitter

My back garden is very small - about 500sqft. I also live near an AM transmitter and requires an AM filter. I would appreciate some general tips on the best approach to receiving HF signals (Ham and ...
5
votes
3answers
322 views

Determining Impedance With An Antenna Analyzer

I need some help interpreting some information from my antenna analyzer (RigExpert AA-35). I want to use the information to impedance match my AM receiving antenna system to AM radios. No ...
5
votes
3answers
407 views

Coax or bifilar windings for a choke?

Making a common mode choke out of bifilar windings has proven rather difficult. For me the difficulty lies in getting the impedance to remain a constant 50 ohms from on the HF bands. I've tried 14 ...
1
vote
2answers
112 views

Why some hams test their baluns with an SWR meter?

There are videos on YouTube that show how to make a 1:1 current balun. When the balun is done some people connect a 100W 50 Ohms resistor to the balun and measure SWR say in 7.000-7.200 MHz range. If ...
0
votes
2answers
281 views

Simple Longwire/Dipole Antenna design

In a couple of days I am going to a mountain cabin and I were thinking about making myself a semi broadband antenna for LF/HF (300KHz - 20MHz or so) for receiving only. I was thinking about creating ...
6
votes
1answer
789 views

How to determine number of turns for a 1:1 balun?

I would like to make a 1:1 balun with М1000НМ ferrite core (magnetic permeability - 1000) and 1 mm thick copper wire using triple bifilar winding. Unfortunately I didn't manage to find a clear ...
1
vote
2answers
519 views

Do I need an 9:1 UNUN for a half-wave end fed?

I was using a 10-ish meter wire as my HF rx antenna. That's all I can install in my QTH. However I realised that my ~10 m wire can be turned into an end fed dipole for 20 meter band. But there is a ...
2
votes
1answer
138 views

Power Amplifier Balun Question

Second (and last hopefully) question on the classic Solid State Design for the Radio Amateurs (SSDRA) book by Hayward et al. Again it's a power amplifier circuit (Chapter 4, pg. 66), and again it's ...
1
vote
2answers
137 views

Using a common-mode choke on symmetrical antenna system

I am curious as to what happens to a symmetrical dipole center-fed with balanced feeder-line. Let's assume the dipole is arranged as a sloper - that means it's not parallel to ground (horizontal). ...
0
votes
3answers
226 views

RF ground and balanced antennas

Suppose that a ham radio setup uses several antennas with a 50 ohm coaxial switch to operate some natively unbalanced antennas and some balanced ones through baluns at the feedpoint. An RF ground for ...
1
vote
1answer
224 views

Folded balun, impedance matching

I am planning on building a half-wave dipole that is fed by a coaxial cable. I found a way to do this on antenna-theory (http://www.antenna-theory.com/definitions/foldedbalun.php). The article talks ...
1
vote
1answer
460 views

Connecting a coaxial cable as feed to a halfwave dipole

I have as assignment to make a half wave dipole antenna, that radiates at 433 MHz. I am trying to figure out how to use a coaxial cable as transmission line. I know that the coaxial cable is ...
6
votes
4answers
1k views

Why do we distinguish between balanced and unbalanced?

I hear all the time, "you need a balun between your balanced dipole and unbalanced coax to stop the common-mode current" when it seems the proper advice is "you need something to stop common-mode ...
2
votes
2answers
413 views

What core material do I need to construct a 1:1 unun for 6M?

I want to build a 1:1 unun for a 6M dipole. Power level 100W. What core material should I use?
1
vote
4answers
1k views

Turn 75 Ω TV “Rabbit Ears” with a balun into a 50 Ω dipole antenna

I got myself a TV "Rabbit Ears" module originally for a TV. It came with a small length of coax, permanently attached to the antenna foot, and a Belling-Lee connector on the other end. My idea was to ...
4
votes
3answers
303 views

Is RF current always confined to the inner diameter of a braided outer conductor of coaxial cable?

Prompted by a previous question found at Using a balun with a resonant dipole -- an answer there included the following text: "For transmission lines (twin-lead or coax) to not radiate, each ...
2
votes
1answer
735 views

Feedline and balun for 80m horizontal delta loop

I am new to HF. I'd like to put up an 80m delta loop. Due to aesthetic considerations I need to use coax to the shack. If tuned for 3.55MHz, I anticipate having a good SWR on 80m, 40m, and 20m. The ...
5
votes
2answers
2k views

Do end-fed dipole antennas need choke baluns?

I have a couple of end-fed wire antennas I bought that came with matching baluns. One has a 9:1 unun, and I'm not sure about the other one. In addition to those, should I also put a choke balun on the ...
5
votes
1answer
412 views

How to build a balun transformer for 2m RX with low insertion loss

I'm looking into ways to match a 137 MHz RX dipole antenna to an unbalanced coax + amplifier. I know there are several types of baluns which can be categorized under magnetic baluns (where there are ...
7
votes
6answers
847 views

Use a TV coax and balun for a poor-man's OCFD?

Can I use TV coax and a cheap TV balun to build a poor-man's OCFD? Marginal performance is acceptable if it saves money. If I could listen to 10% of transmitters within a 100 mile radius that would be ...
1
vote
1answer
48 views

Can I use two voltage baluns to make a common mode choke?

I have two 1:4 voltage baluns. If I connect them together so that I have 1:4-4:1, is that the equivalent of putting a 1:1 common mode choke on my feed line?
2
votes
3answers
4k views

How do you construct a 1:1 balun?

I have been researching how to construct a 1:1 current balun. I have a few questions and am looking for feedback on what I plan to do. First, I want to use the balun from 10m to 160m at 100w. I plan ...
12
votes
3answers
6k views

Where are the baluns for VHF and higher? How can one be made?

In another question, commenters recommended that I look into adding a 1:1 balun to a dual-band dipole to eliminate the feedline as a radiator. As I understand it, a 1:1 balun also functions as a choke,...
2
votes
2answers
1k views

Balun and tuner configuration for multiband dipole

I'm putting up a multiband dipole in some tall trees. (Perhaps it's more correct to call it a "dipole-doublet"). The situation I'm imagining looks like this: The legs of the antenna are each 100 ...
1
vote
2answers
130 views

Serial matching stub combined with RF choke

If I use RG6 coaxial cable in odd multiples of 1/4 wavelength as a serial matching stub, can I also use it, without modifying the length, as a coiled RF choke balun at the antenna feed point?
2
votes
1answer
117 views

What effect does a balun have on s-parameter, beam patterns?

I have a dual-dipole antenna with a subreflector slightly above it and a ground plane below it, and attached to the ground plane is a balun. While simulating in CST microwave studios, I didn't include ...
3
votes
2answers
233 views

Why don't baluns require precise conductor spacing as in twin-lead?

This is a follow up to another recent question of mine: Does a balun need to be made with coax? In that question, we establish that a choke balun doesn't actually work by protecting the "third ...
9
votes
2answers
3k views

Does a balun need to be made with coax?

The short version My understanding is that one of the main reasons to use a balun with coax is to prevent the outside of the shield from becoming part of your antenna system. If that's the case, won'...
3
votes
1answer
391 views

Balun identification from picture

I thought maybe this was a 4:1 balun, but a number of 4:1 single core balun diagrams that I found online had different connections. N1HFX's balun page and the bottom of G4WPW's page show a connection ...
1
vote
2answers
132 views

what is choking reactance in TLT?

I was studying about the Guanella 1:1 balun and came across the term "choking reactance". What does this mean? Why does its value need to be large?
2
votes
1answer
516 views

Will adding a balun to a full-wave dipole help?

I have made a dipole for 40 m, no swr to speak of on 7040 kHz, but I've been told that it should also work on 20 m as it is 20 meters long (2× 9,92 m) but there I get SWR in the 7-9 range. Will this ...
5
votes
2answers
466 views

Why aren't there baluns that do BOTH balanced/unbalanced transformation and common mode current attenuation?

I have read myself blue, about baluns. Especially 1:1 ones. Some claim they're only there to balance the unbalanced signal, and that's what's in the name also, but I find several that claims that the ...
8
votes
2answers
2k views

Why isn't twisted pair used for feedlines?

My son was asking about some Ethernet cable (Cat 5 unshielded twisted pair), and since he recently passed his Technician exam and we both have "radio stuff" on our minds, I tried to make the analogy ...
1
vote
1answer
279 views

how does slotted coax Balun eliminate common current?

how does slotted coax Balun eliminate common current? why the length of the slot should be quarter wavelength?
2
votes
1answer
459 views

What do we mean by “RF in the shack”?

What does "RF in the shack" mean? How does it interfere with devices around coax?
4
votes
2answers
2k views

How to measure a balun for effectiveness?

It seems there are almost as many "balun" designs as there are web pages about "baluns". There's lots of accusations pointed in all directions ("design Z isn't a balun OR a choke", "design Y is ...
20
votes
3answers
25k views

Why are some 1:1 current baluns twice as complicated as others?

I would like to add a balun/choke to my dipole for the reasons outlined in Using a balun with a resonant dipole. In the spirit of continued kit and/or DIY building for my ham shack, I set out to ...
2
votes
1answer
1k views

Balun and impedance matching suggestions for dipole antenna

I'm a newbie who is attempting to build a half-wave dipole antenna that will be located in the rudder of a sailplane. 123.3 MHz is the most important frequency to me, although it's reasonable to ...
4
votes
3answers
2k views

Recommended 9:1 unun core type(s)

I would like to construct a 9:1 unun that connects my QRP transceiver to a random-wire antenna. The transceiver's antenna connection is an unbalanced BNC jack and the random-wire antenna is, well, a ...