Questions tagged [antenna-construction]

Materials and methods for building antennas, and design of supporting (non-conductive) structures. For design of antennas themselves, use [antenna-theory] instead.

Filter by
Sorted by
Tagged with
2
votes
0answers
50 views

What's the issue with stainless steel antenna elements? [duplicate]

New ham, here...getting motivated to build some antennas to experiment with and so far my research has shown that stainless steel is not a desirable metal for creating antenna elements - which is a ...
1
vote
4answers
113 views

Which 10 m antenna will give the most rejection in one direction for received signals which are vertically polarized?

I want to null out a particular direction so that i can't receive some vertically polarized interference on 10 m coming from that direction. Which 10 m antenna will give the most rejection in one ...
1
vote
3answers
127 views

Need antenna for mobile mag-mount LPFM broadcast 88.3 MHz

I am doing some temporary FM broadcasting for car events such as COVID-safe car parades and drive-in movies. The terrain is horrible, urban areas with lots of buildings. The cars snake around a city, ...
1
vote
2answers
83 views

Will close-loop metal hangers affect antenna radiation?

I'm working on a kite-supported antenna for an 80m QRP rig -- to be flown at beaches, on mountaintops, and possibly other places where I want to work HF but don't want to lug poles or give up ...
1
vote
3answers
374 views

Bandwidth, Q-factor, Radiation Eff calculations

Is it possible to give approximate answers about what an antenna is capable of? There are a lot of formulas out there, but every single one I found is based on actual measurement; input, output, SWR ...
1
vote
2answers
89 views

How to match transmitter to Beverage antenna

Beverage antenna consist of pair of transmission lines - one being the "antenna proper", the other ground. The antenna is being fed via open feed line ( approximately 450 Ohms ) - one side ...
1
vote
3answers
145 views

Can I build a guanella balun using single strand wire instead of coax?

I am trying to homebrew a cobweb antenna and need some help understanding the guanella balun used as described here: http://www.karinya.net/g3txq/cobweb/ This author used RG316 coax around the ...
1
vote
1answer
214 views

Yagi elements connected to boom?

I'm considering building this yagi for some local contests: http://www.i1wqrlinkradio.com/antype/ch90/chiave3.htm. The question is should the elements be electrically connected to the boom or not? I ...
1
vote
2answers
152 views

Is a “shorted” coax feedline ok for a G5RV type antenna?

I have "inherited" what I believe to be a G5RV antenna with two 51 foot wire centerfed radiators. If I remember correctly from measuring 2 months ago, there is about 31 feet of 450 ohm ladderline ...
1
vote
2answers
2k views

How to best connect an FM transmitting GPIO pin to an antenna?

I'm trying to use a RaspberryPi3 as a FM transmitter, using pifm and/or PiFmRds to send audio in 88-108 MHz band. The RPi can then use the GPIO-4 pin to transmit between ...
1
vote
1answer
53 views

Lightning protection for a vent stack antenna

I've seen ham radio antennas that slide over a vent stack. The usually way to connect them to the transceiver is to lay the feedline across the roof. However, the manufacturer provides instructions ...
1
vote
1answer
255 views

How do I use multiple antennas with two or more radios?

I'm building multiple antennas tuned to different amateur bands and would like them connected to my SDR for remote listening and analysis, and a handheld radio for transmission, which I may upgrade or ...
1
vote
2answers
79 views

How many turns of wire inside 60 cm shielded loop antenna (9kHz - 30 MHz). How can I find this number without destroying the antenna?

Lots of information about shielded loop antennas is available on the internet. However, antenna manufacturers do not indicate the number of turns. How can I find the number of turns of a manufactured ...
1
vote
1answer
115 views

440MHz collinear dipole array - suitable coax?

friends! Finally found my next antenna project..a collinear dipole array for the 70cm US ham band. The general idea: (image courtesy https://link.springer.com/referenceworkentry/10.1007%2F978-981-...
1
vote
1answer
43 views

What is the maximum antenna cable length allowed in GNSS application?

I am beginner in designing GNSS receiver design and facing concern while testing the high precision GNSS survey.I am using GNSS survey grade antenna for my GNSS receiver application testing, the ...
1
vote
1answer
68 views

Is there a suitable alternative to using a metal pole to mount a vertical yagi apart from wood and fiber glass?

Does anyone know if a non-metallic pole approx. 4 m long is available that i can use to mount a vertical 10 m 4 element yagi ? that is not wood, PVC or fiber glass as these are either too heavy or not ...
1
vote
1answer
95 views

Radio antenna for my FM receiver / Android FM

I want to make a radio antenna at home which will be able to receive all FM frequencies for my FM radio or Android FM. How do I make it? Frequency it can catch : 88 - 108 MHz Thanks.
1
vote
1answer
56 views

Are stainless steel studs acceptable as a feedpoint connector for an aluminum loop antenna?

Similar to Will stainless steel bolts work with my copper antenna? however my concern here is with electrical properties. With copper antennas I never gave it much thought... just solder the wire. I ...
1
vote
1answer
65 views

Effect of small amount of metal on twin-lead

I have a G5RV Jr. antenna on a fiberglass mast at 10m height. The only metal on the mast is a 1/8" thick steel guy ring with stainless steel snap links, plus a few small metal screws. Hanging freely,...
1
vote
1answer
92 views

RF inert adhesive for building antennas in the UHF to low GHz region

I want to experiment with different mechanical designs for some Yagi antennas for 440 MHz through perhaps 2.3 GHz. I am looking for some adhesives and/or potting-like materials that would be ...
1
vote
1answer
100 views

Resistance of antenna dipoles

A quick question: Is it a disaster if the two legs of a v-dipole antenna are different resistances? Thanks.
1
vote
2answers
606 views

Linear-Loaded Cage Dipole?

I've recently learned about linear loaded dipoles as one way of building a physically shortened antenna. As I understand it, any shortened antenna will have reduced bandwidth and linear-loaded dipoles ...
1
vote
2answers
292 views

Measured forward power less than “usual”

I've just tried making my own J pole antenna. While matching for lowest SWR on the SWR meter, I noticed that my FTM400 didn't show 5 W forward power. I hardly saw the reflected power needle move so I ...
1
vote
2answers
548 views

Airband VHF antenna challenge

I have a very difficult antenna design/installation challenge. I need to install an VHF antenna (118 to 140 MHz) into a nearly all carbon fiber glider. The radio provides 5 watts and 50 ohm, and most ...
1
vote
1answer
28 views

How to calculate of shielded loop antenna correction factor without extra antenna measurements

A lot of article about 60 cm shielded loop antennas and how to measure antenna factor using antennas with already known antenna factor. But for example if I have one shielded loop antenna (...
1
vote
1answer
90 views

Need help understanding the gain on antenna pattern plots

My understanding is that the value of the axis (like -10 / 0 dB) refers to the maximum antenna gain (e.g. 12dbi). So, if a ...
1
vote
3answers
349 views

2m 5-element yagi with staggered driven elements

I have seen sketches of 3-element 2m yagi antennas in which the driven dipole elements are staggered i.e., one element is positioned slightly in front of the other along the length of the (plastic) ...
1
vote
2answers
93 views

Matching a 188 ohm antenna to an unbalanced input that expects a 50 ohm antenna

I am new to RF field and trying to use an Archimedean Spiral Antenna design from this paper to capture 915MHz RF for the P2110B power harvester chip. The estimated antenna impedance is 188 Ohm (see ...
1
vote
2answers
93 views

Identify these components

First post here yay! I am repairing Shengda sdhf dual band antenna (looks similar to a Comet x50) it showed a SWR of >3 on both UHF and VHF. I opened it up and the only connection I could see ...
1
vote
3answers
889 views

Better antenna for 433 MHz

I am using a FS1000a Transmitter and a MX-RM-5V Reciever for transmitting Sensor Data inside my flat to an Arduino Device. (13 Chars every 10 Seconds) The same Transmitter type is also used for ...
1
vote
1answer
262 views

What are the wire lengths of the RadioWavz OCF 40m dipole?

I was recently gifted the RadioWavz DX40 Short sans wire. I have the balun and the wound inductor, but can't find any information as to the proper lengths of wire for this antenna. I can find general ...
1
vote
1answer
3k views

Homebrew 2 meter Yagi construction

Here is what I have • A Baofeng Uv-82 transceiver • A 1/2 inch 10 foot PVC pipe • 3 1/4 inch x 36 inch Aluminum rods • 2 1/4 inch x 48 inch Steel rods (I know they'll rust, it's just temporary to ...
1
vote
0answers
83 views

How do I Construct a Simple FM Antenna?

I recently bought a cheap stereo amplifier with built in FM receiver from Amazon at the first link below. Testing it out today I found the FM reception to be sub-par. All of my local stations that I ...
1
vote
0answers
36 views

Unsure how to assemble Shakespeare SSB antenna; not working [closed]

Have 23 foot Shakespeare SSB antenna. Can not connect through the side feed termination band? Antenna not working? What is the band supposed to look like? Is the termination band supposed to be ...
0
votes
2answers
119 views

Antenna Basics - Open/Short Circuit & Half-Duplex/Full-Duplex

I am beginner in the Antenna theory and I have a few basic questions. Please help me to clarify my understandings related to the basics which I have read. And this question has 3 basic questions. ...
0
votes
2answers
81 views

Proper magnetic mount placement on roof

I have a Nissan Versa 2012 (hatchback). It comes with one of those default antennas at the back/center of the roof, for listening to AM/FM radio stations. I have a dual band mag-mount (TRAM 1185), ...
0
votes
2answers
1k views

Simple Longwire/Dipole Antenna design

In a couple of days I am going to a mountain cabin and I were thinking about making myself a semi broadband antenna for LF/HF (300KHz - 20MHz or so) for receiving only. I was thinking about creating ...
0
votes
1answer
67 views

Will rewiring this antenna change the characteristics?

Speaking of the antenna in this question: What kind of 2 meter antenna is this? The connections are rusted and corroded so I'd like to rewire it. If I move the shield from where it is currently ...
0
votes
1answer
200 views

pull-up inductors for a differential PCB trace antenna

Trying to figure an antenna for the Si4012 RF chip. Page 26 of https://www.silabs.com/documents/public/application-notes/AN639.pdf talks about feeding the two sides of the loop antenna through two ...
0
votes
1answer
46 views

60cm 9 kHz 30 MHz Shielded loop antenna behavior as a transmitting antenna

I know how shielded loop antenna work as a receiver antenna. (How behave electric and magnetic field). But I can not understand how shielded loop antenna works as a transmitter. Will it produce only ...
0
votes
1answer
73 views

Pondering variations on the vertical bazooka antenna

I've seen these antennas built out of coax that are called a bazooka vertical. It's a kind of 1/4 wave vertical, or perhaps a 1/2 wave dipole. Constructing such an antenna is to roll back the outer ...
0
votes
3answers
215 views

How can a vertical Yagi for 10 m be mounted on on a vertical metal mast and be made to work properly? [duplicate]

From a reply to a previous post I've been told that a horizontal tube half a wavelength long mounted right at the junction between the boom on a vertically mounted yagi and a vertical metal pole will ...
0
votes
1answer
94 views

Antenna Type of a Chinese Antenna

Recently, I have received an antenna from one of the Chinese manufacturer and they haven't disclosed the detailed specification with us. Below is the picture of my antenna (please ignore the ...
0
votes
1answer
212 views

NFC coil matching - Q factor improvement

I have been trying to match my NFC reader coil of size 20*20 cm with a three element circuit - one capacitor in series, another in parallel and one resistor in parallel. I have been using Texas ...
0
votes
1answer
284 views

RCA victor 35x tube radio loop antenna replica?

There is this one youtube video I have not been able to find again, where someone with a similar model radio was making replica of the original loop antenna on the back. I am wanting to make a ...
0
votes
1answer
82 views

What parameters are currently possible in a directional antenna less than 5mm long?

I'm curious what kind of directional antennas could fit inside a cell phone, which would require it to be 5mm or less in its longest dimension. I know that the length of a directional antenna is often ...
0
votes
1answer
97 views

Can wood be used to build 6m quad? [closed]

Could I use wood to build 6m quad? If not, what material(s) would be better/more useful?
0
votes
0answers
74 views

How to stabilize an antenna

I have an antenna on a building. It is made of steel and is about 10ft long. It wobbles a bit in high winds. It is not going to do a Tacoma Narrows but it is a bit annoying. Can I tie stainless steel ...
0
votes
0answers
86 views

what frequencies is this antenna cut for?

I just bought a magnet-mount whip antenna at a garage sale. It has no brand markings anywhere on it. it is 32" long overall but is broken up into three segments by what appear to be two small ...
0
votes
0answers
54 views

Omni 144 MHz antenna

I plan to build omni antenna. My goal all about better gain versus a 1/4 wave antenna. I am curious about radial position of the legendary ARX2B Ringo Ranger. Why is the position in below feed point? ...