Questions tagged [antenna-construction]

Materials and methods for building antennas, and design of supporting (non-conductive) structures. For design of antennas themselves, use [antenna-theory] instead.

Filter by
Sorted by
Tagged with
6
votes
4answers
461 views

Weather-proofing antenna connections

Here's a problem: you buy a fancy new vertical for a fair bit of coin, but there's no coax connector on the thing. There are just screw terminals. You need to attach coax to it, but in such a way ...
9
votes
1answer
1k views

How to combine two 50 Ω antennas such that they appear as one 50 Ω load?

I'm looking for a simple way to impedance match an array of two 50 Ω antennas so that when they are combined they appear as one 50 Ω load. Assume that both antennas are identically constructed, are ...
8
votes
2answers
391 views

Is steel or aluminum structurally a better material for catenaries?

I understand that steel is not a good material for antenna wire, but let's consider that I'm using the wire for purely structural support, or I am cladding it with copper to address the RF ...
4
votes
2answers
2k views

Can an HF antenna be put inside a tree?

There are some trees around with branchy tops that seem wider than half of 10M, maybe even half of 20M, and above the nearby rooftops. Can a wire dipole or a vertical be mounted inside a tree? If so,...
5
votes
2answers
4k views

Is copper-clad steel a good material for wire antennas?

There are some people selling steel wire plated with copper for making wire antennas. Perhaps the most well-known brand of this product, Copperweld, makes at least two kinds of copper-clad wire, ...
33
votes
4answers
45k views

Effect of different metals for antenna elements

Other than rust, corrosion, and other reactions with air that would make the use of a metal unfavorable, how do different metals affect the performance? Let's give Yagi an example: Let's say I use 4 ...
6
votes
1answer
6k views

Noise bridge use in antenna construction?

How does a noise bridge work? And how can a noise bridge be useful in building, testing, and/or tuning an antenna?
1
vote
1answer
2k views

Homebrew 2 meter Yagi construction

Here is what I have • A Baofeng Uv-82 transceiver • A 1/2 inch 10 foot PVC pipe • 3 1/4 inch x 36 inch Aluminum rods • 2 1/4 inch x 48 inch Steel rods (I know they'll rust, it's just temporary to ...
7
votes
1answer
765 views

How does aluminum siding on a house affect an inverted-vee antenna next to it?

My two-storey house is wood with alumninum siding. I had wanted to install an inverted-vee antenna with its midpoint hanging from the eave, and endpoints near the ground, but this would place the ...
16
votes
1answer
7k views

How to detect common-mode currents or “RF in the shack”?

Let's say we already know that if your antenna is not suitably constructed or connected then you can get current on the shield of your coaxial feed line which will flow through the shielding/grounding ...
8
votes
1answer
3k views

What's an appropriate core material for a loopstick antenna?

A loopstick antenna, if you don't know, is a coil of many turns around a high permeability core. They are frequently encountered in AM receivers and look like this: This particular example is ...
6
votes
4answers
5k views

Does oxidation of the antenna elements have any impact on the signal quality of the station?

So I'm still QRT; apart from a brown-out on the rig, the support on the inverted-vee toppled over in high winds. Thanks to the topple-over I discovered the conductors (SWG 16 bare copper) had ...
5
votes
3answers
3k views

What type of solder is best suited for radio and electronic use?

Many types of solder are available today, such as acid-core, silver, rosin-core and aluminum solder. What kind should I use for building antennas and radio equipment? Why? From test question: T7D08
6
votes
1answer
938 views

Are there easier ways to make traps than coax and plastic pipe?

I recently built an antenna for my attic inspired by http://degood.org/coaxtrap/. I found making the coax traps very time consuming and frustrating to tune. I got to thinking about 3D printers, and ...
9
votes
2answers
1k views

What is the largest gauge (thinnest diametre) wire I may use as an antenna?

A follow-up to Good wire for wire antenna? I'm QRT at present - thanks to fooling around with just a couple of diodes and PVC capacitors instead of a well-regulated supply. The antenna I used earlier ...
4
votes
4answers
777 views

Is string trimmer line suitable for supporting antennas?

In searching for suitable materials for a wire antenna, I found a few mentions of using string trimmer line to hold up each end of the antenna. This would be a nice option as it is readily available ...
8
votes
3answers
18k views

How would I modify a satellite dish to transmit and/or receive to a Baofeng UV-5r plus? ( A handheld transceiver) If it's possible

I have an old satellite dish just lying around and was wondering how to hook it up to my baofeng uv-5r plus.
8
votes
1answer
673 views

Do I need a SWR meter for a basic 2 meter antenna?

I have a 5 watt 2 meter handheld transceiver and want to build a helmet with an antenna, microphone (with VOX enabled) and earpiece for the radio. For the antenna part, I just want to do something ...
8
votes
3answers
2k views

Will anodizing or powder coating or wetcoating (painting) antenna elements affect performance?

I want to put up a small tower and beam on my roof, but I don’t want the aluminum to “stick out” and want it to be unnoticeable as possible. I would think black anodizing would be the best solution ...
10
votes
1answer
911 views

Can I have multiple inverted-vee antenna fed by a single coax?

A friend who recently received his call is planning to setup an inverted-vee for 40/20m bands. Our take is the signal will take the path of least impedance into the correct length antenna wire. ...
0
votes
1answer
96 views

Can wood be used to build 6m quad? [closed]

Could I use wood to build 6m quad? If not, what material(s) would be better/more useful?
14
votes
5answers
36k views

Good wire for wire antenna?

What properties should I look for in a good wire for building a wire antenna? Could anyone recommend something specific for me?
2
votes
5answers
548 views

Metal for antenna construction?

What do I need to consider when choosing metal for an antenna? How do I determine what thickness to use?
13
votes
1answer
5k views

What is the purpose of a balun and a unun in a feed line?

I have never understood how a balun or a unun works and under which situation I need to use either of them in an antenna feed line.