Linked Questions

29
votes
6answers
33k views

Can I reduce RFI/noise at the antenna?

Recently, the power was out in my neighborhood for an extended period of time. I fired up my HF rig using battery power and was amazed at the lack of noise across the HF bands. When the power grid ...
24
votes
3answers
36k views

Why are some 1:1 current baluns twice as complicated as others?

I would like to add a balun/choke to my dipole for the reasons outlined in Using a balun with a resonant dipole. In the spirit of continued kit and/or DIY building for my ham shack, I set out to ...
19
votes
5answers
9k views

How can I protect equipment against a lightning strike?

A lot of aerials (almost by design) would be rather good attractors of lightning. What steps do I need to take in the field to keep my gear safe against a lightning strike? I'm presuming the obvious ...
14
votes
4answers
6k views

What does the addition of a shield to a small loop accomplish?

A small shielded loop is an antenna with a loop of wire, smaller than 1/10th of a wavelength in diameter, also surrounded by a shield. Often, they are constructed from coax. There is a gap in the ...
13
votes
3answers
7k views

How do I prevent radio signals from tripping a GFCI?

My wife woke up several nights by a metallic "thunk". It happened to be while I was talking on 10 meters and turned out to be the ground fault circuit interrupter (GFCI) on her hair dryer cord. ...
13
votes
4answers
3k views

Handheld Dipoles

A problem with handheld devices is poor grounding. I read from someone else's question that dipoles don't need a ground. Why don't they make little handhelds with two antennas instead of one, or a ...
12
votes
2answers
4k views

Is there an optimum Antenna Feedline Length for mobile installations?

I bought a ham radio antenna mounting kit for my car that includes ~16' of coax. One end has a trunk lip NMO antenna mount, the other end has a re-solderable PL-259. I asked the sales person if it is ...
10
votes
5answers
5k views

Grounding a second-story shack with an outdoor antenna

My shack is on a second story, really far away from the house ground. To run a ground from my equipment to the outside/ground is a run of at least 60-75 feet. The antenna is at least 100 feet away as ...
9
votes
6answers
32k views

Is there a simple, DIY, antenna suitable for HF receive only?

So the antenna I'm thinking about doing might be* way too large for my property. Is there another simple, cheap, DIY antenna I could try on my receiver? I know I'm going to want to hook it up and ...
9
votes
2answers
8k views

Grounding VHF base station antenna

I'd like to install an outdoor dual band VHF/UHF base station antenna, a simple pole antenna like the Comet GP-1. I live in an area where lightning is rare, but not unheard of. Should I drive ground ...
6
votes
8answers
9k views

How does the length of a metal sleeve around a (shieled) coax cable affect antenna performance?

A post on http://adsbexchange.com/forums/topic/beginners-2-cantenna-easy-diy-antenna-to-improve-rangeplane-count uses a $\frac{\lambda}{4}$ sleeve made of a pop can beneath a $\frac{\lambda}{4}$ wire ...
6
votes
7answers
8k views

What is the attraction of vertical antennas for HF?

I understand that MW broadcast stations use vertical antennas because that polarization works much better for groundwave propagation. But in amateur radio, I would assume the focus for communications ...
6
votes
2answers
1k views

Dipole Antenna Current Distribution at any Time Instant

Above is a connection of half-wave dipole antenna. The book states that the current profile is same at any given time instant on both the radiators, each of quarter wavelength length. Now my ...
6
votes
2answers
2k views

Understanding coax radiation and “current on the shield”

I'm having trouble understanding what seems to be the fundamental principle behind baluns (and probably other related topics). Perhaps some of my confusion comes from an audio background, where one ...
6
votes
4answers
3k views

Why do we distinguish between balanced and unbalanced?

I hear all the time, "you need a balun between your balanced dipole and unbalanced coax to stop the common-mode current" when it seems the proper advice is "you need something to stop common-mode ...

15 30 50 per page