Linked Questions

4
votes
3answers
130 views

When a dipole antenna is fed via coax, what powers the ground-side of the dipole?

I've been trying to understand how dipole antennas work, and I believe I understand the basics when they're fed via a balanced feed line. In fact, every dipole physics YouTube video and web page I can ...
1
vote
2answers
168 views

Loop Antenna Construction

I have a loop antenna. When I connect the probe from my oscilloscope, does the probe also act as an antenna? If so, how should I fix that? I read about feeding technique, but I still do not ...
0
votes
3answers
82 views

Is there an instance where you can directly feed a half wave dipole with coaxial cable without having to worry about balanced to unbalance?

Like the question says, can you feed a dipole with coax with no ill effects? Nothing else in the system, just the antenna and the cable.
1
vote
1answer
65 views

What lengths of coaxial feed lines should you avoid?

Are there lengths of feed line to avoid or ones that may cause problems with an antenna system? For single band use. Appendix: The run of coaxial will be for the 10 metre band. I would imagine this ...
3
votes
1answer
154 views

What is the optimum length for a random longwire on 10m?

I have all the space in the world and wish to errect a single random longwire to use on the 10 meter band only. I understand that once such a wire is very long, losses associated with the wire itself (...
3
votes
2answers
45 views

Should the earth rod be incorporated in the total length of an RF grounding system?

I have installed a grounding system just outside my radio shack and was careful to avoid a quarter wavelength or multiples thereof (for single band use), or anything in total length that is close to ...
3
votes
1answer
90 views

Is this “floating” output single-ended or differential and against GND or VCC?

I'm looking at a simple FM transmitter output (see picture). It is from the collector of a transistor and it goes through a DC blocking capacitor before the antenna would be connected. The entire ...
0
votes
1answer
143 views

Pondering variations on the vertical bazooka antenna

I've seen these antennas built out of coax that are called a bazooka vertical. It's a kind of 1/4 wave vertical, or perhaps a 1/2 wave dipole. Constructing such an antenna is to roll back the outer ...
0
votes
1answer
198 views

Is shortening a half wave dipole to make it resonant by removing the inductive reactance a good idea?

A dipole which is exactly one half wave length allows reflections within the antenna to be in phase with the applied signal. To me it seems that this situation gives an antenna which will produce the ...
4
votes
2answers
559 views

Does a dipole require a 1.5:1 balun?

Dipoles ideally have 72 ohms impedance. I know most of the time this isn't what one gets and it can vary a lot. But let's assume we can build this perfect dipole that exhibits this impedance. Why do ...
0
votes
3answers
328 views

To folded dipole, or not to folded dipole?

I currently operate a 20M half-wave dipole with a balun. It's a little lower than ideal, but it gets me on the air. I've read about folded dipoles. But I've found contradicting information about them....
2
votes
2answers
119 views

Grounding of a portable setup

I am occasionally using an extremely simple shortwave portable setup consisting of a battery, the transceiver, a short coax feedline and a vertical half-wavelength vertical antenna with a transforming ...
3
votes
1answer
115 views

Do these magnetic field measurements of end-fed and center-fed half-wave dipoles corroborate measurements made by antenna experimenters?

Using a sensor and procedure discussed in my article, I made the following plot comparing the magnetic field strength along a 30m-band half-wave dipole fed at center and one end. Key points include: ...
3
votes
1answer
2k views

3 Band (80-40-20 Meter) Fan Dipole Tuning Question

I built a fan dipole according to the basic instructions in the SRI publication describing the theory and basic design. My questions is about next steps in tuning for the various bands. I am ...
1
vote
4answers
2k views

Is the ground on the back of the Icom IC-7300 an electrical or RF ground?

On the back of the Icom IC-7300 there's a ground connector: The manual goes on to say this: Is this an electrical or RF ground?

15 30 50 per page