Linked Questions

2
votes
2answers
162 views

Reciprocity and SWR [duplicate]

If someone has a high SWR, obviously their signal will not make it out as far due to reflections. However, they will still be able to hear relatively well. I have noticed for receive, a high SWR may ...
9
votes
6answers
30k views

Is there a simple, DIY, antenna suitable for HF receive only?

So the antenna I'm thinking about doing might be* way too large for my property. Is there another simple, cheap, DIY antenna I could try on my receiver? I know I'm going to want to hook it up and ...
18
votes
3answers
8k views

Why do I need to tune an antenna?

I've heard that when an antenna is set up, it needs to be tuned to reduce reflective power back into the radio. Is this always necessary, and if so how would I go about tuning it?
8
votes
3answers
12k views

How can I reduce the noise coming in from an RTL-SDR dongle?

I've recently received an RTL-SDR dongle, and I'm picking up a lot of noise that is probably coming from my PC, especially a lot of "spikes" on the 2M band. I've already started using a USB extension ...
5
votes
2answers
7k views

How to construct a loop antenna for receiving HF?

I have a unused hula-hoop in my garage, and I ran some stranded speaker wire around it once, and attached one side of the wire to the coax shielding, and the other to the coax core wire. Is this the ...
8
votes
3answers
4k views

How do I extend broken coaxial cable?

I have a piece of 75 ohm coaxial cable of unknown type (outer diameter is around 7 mm) which has developed a breakage in the center conductor (which is stranded). This cable is an adapter cable which ...
9
votes
2answers
757 views

If two antennas of 50 Ω and 377 Ω have VSWR=1:1, then which one is more efficient?

If there are two antennas of 50 Ω and 377 Ω (same as the intrinsic impedance of air) impedance with 0 $\Omega$ ohmic resistance, and they are exactly matched with their transmission line, then which ...
5
votes
3answers
1k views

Determining Impedance With An Antenna Analyzer

I need some help interpreting some information from my antenna analyzer (RigExpert AA-35). I want to use the information to impedance match my AM receiving antenna system to AM radios. No ...
1
vote
4answers
2k views

Turn 75 Ω TV “Rabbit Ears” with a balun into a 50 Ω dipole antenna

I got myself a TV "Rabbit Ears" module originally for a TV. It came with a small length of coax, permanently attached to the antenna foot, and a Belling-Lee connector on the other end. My idea was to ...
10
votes
1answer
2k views

How does a “chip antenna” work?

How does a tiny surface-mount "chip antenna" for the 2.x thru 5.x GHz frequency bands work? What allows such a tiny item to radiate or receive RF with some amount of efficiency? What allows a chip ...
1
vote
3answers
1k views

How to attach a magnetic loop antenna to the 50Ω coax of an RTL SDR?

I'm planning to make a magnetic loop antenna mainly for receiving LW, MW, and SW radio broadcasting bands, as well as perhaps the 2.2km band and 630m band. (Not all of them with the same antenna, I'mm ...
5
votes
5answers
485 views

Signal path to maximize RFI rejection in an urban environment

Urban ham here (Cambridge, MA - FN42ki - KC1JZE) looking for tips to make this hobby possible in the city. I rarely can hear both sides of HF phone transmissions, and have yet to make contacts despite ...
5
votes
3answers
2k views

How to feed coax from inside car?

What is the best (or standard) way to get coax from the radio in the car to the outside of the car without smashing it and damaging the line? If I just put it through the door crack, it seems to ...
2
votes
2answers
1k views

Does increasing the number of turns on a loop antenna decrease frequency operation?

Lets say I want to make a VLF loop antenna for a Sub AM radio band. I don't want a full wavelength because that would be a humongous antenna. Would I wind more turns of wire to decrease the frequency ...
2
votes
3answers
4k views

How does the antenna length affect signal transmission/receipt in different bands?

My Canadian Amateur Radio Basic Qualification Study Guide tells me that my antenna length is specific to the wavelength I wish to broadcast on and gives a formula that equates to antenna length = half ...

15 30 50 per page