Linked Questions

4
votes
2answers
236 views

Dipole increased CM current using choke balun

My 20 meter inverted vee dipole is fed with 56 feet of 50-ohm coax. The SWR measures 1.2 at the center of the band. According to http://arrl.org/grounding a balanced antenna doesn't need a ground, so ...
4
votes
2answers
3k views

Does effective grounding of mobile (vehicle) antenna mounts address common-mode currents?

While researching how best to install my mobile amateur radio in my car, I didn't understand if there was optimum Antenna Feedline Length for mobile installations? Understanding that this is caused ...
3
votes
2answers
119 views

Interpreting (noise) signals from a small untuned shielded loop

This a follow up from this question: QRN: How to chase down a solid S9 noise floor on 40m only Focusing on how to interpret the signals received with an electrically small, untuned "shielded loop&...
3
votes
2answers
48 views

Should the earth rod be incorporated in the total length of an RF grounding system?

I have installed a grounding system just outside my radio shack and was careful to avoid a quarter wavelength or multiples thereof (for single band use), or anything in total length that is close to ...
1
vote
2answers
194 views

Loop Antenna Construction

I have a loop antenna. When I connect the probe from my oscilloscope, does the probe also act as an antenna? If so, how should I fix that? I read about feeding technique, but I still do not ...
1
vote
2answers
173 views

Troubleshooting 5BTV antenna

I have a Hustler 5BTV antenna i resurrected after a previous monopole succumbed to birds. It is giving me a world of trouble trying to get it tuned for resonance. For those not familiar with the ...
1
vote
2answers
845 views

Exactly why do some SWR meters give a changing reading depending on the length of coax used to connect to an antenna?

Following is my understanding of some theory and the questions are at the end. Is this right ? ... A standing wave is an AC waveform oscillating at a particular frequency which has a varying ...
1
vote
2answers
265 views

Using a common-mode choke on symmetrical antenna system

I am curious as to what happens to a symmetrical dipole center-fed with balanced feeder-line. Let's assume the dipole is arranged as a sloper - that means it's not parallel to ground (horizontal). ...
1
vote
2answers
765 views

Multi-part question. correct length of rg-8x coax to connect 2 meter HT to 50 ohm yagi

What it the optimal number of wave lengths of RG-8X coax to connect my Icom IC V80 HT to a 50 ohm Jetstream JTBM270 Yagi (3 elements 2m/5 elements 70cm)? Odd or even number thereof? Will running the ...
0
votes
2answers
203 views

2 meter coax cable balun dimensions for use with a ground plane?

I have a commercially manufactured ground plane antenna for 2 meters. It will be fed with about 150 feet of RG 8/U . I've seen pictures of a coil of the feed line going to a 2 meter ground plane; this ...
7
votes
1answer
3k views

How to determine number of turns for a 1:1 balun?

I would like to make a 1:1 balun with М1000НМ ferrite core (magnetic permeability - 1000) and 1 mm thick copper wire using triple bifilar winding. Unfortunately I didn't manage to find a clear ...
3
votes
1answer
118 views

Do these magnetic field measurements of end-fed and center-fed half-wave dipoles corroborate measurements made by antenna experimenters?

Using a sensor and procedure discussed in my article, I made the following plot comparing the magnetic field strength along a 30m-band half-wave dipole fed at center and one end. Key points include: ...
3
votes
1answer
394 views

How can I tell the frequency without an oscilloscope, or frequency counter?

Just going through the RF oscillator listed on SM0VPO's web-site. I replaced C1 by a reverse biased 6A8, and used an E-core transformer pulled out of a Compact Fluorescent Lamp instead of an inductor ...
2
votes
1answer
101 views

Should I run RG8x / mini8 zip tied to a cat 5e ethernet cable?

I'm running a feed line from the end of my amplifier to the antenna for HF transmissions. I'm using RG8x / mini 8. There's an existing pathway through my house I'd like to use that has a cat 5e ...
1
vote
1answer
626 views

How to assemble an antenna (impedance matching methods)

I got the following plans off Martin E. Meserve's website. How do I go about assembling the antenna once I have the elements and boom? What is the impedance of the driven element? Do I need baluns ...

15 30 50 per page