I tried but failed to decode WSPR using Tecsun PL-600 receiver that tunes in 1KHz step. I heard tones with good SNR but cannot be decoded. So, I mis-set it somewhere.

  1. Is it correct that transmission is around 10.140200MHz, with a few Hz bandwidth?

  2. What are the four symbol RF frequencies? I seem to read documentation saying that they are 10.140200 + (0_to_3 x 1.4648Hz). I observed WSPR sound card output, using Spectrum Lab software, and they are spreading from 1497 to 1503 Hz, instead of 1500 to 1506Hz. Where did I miss?

  3. On a 'normal' receiver, should I set the receiver frequency to 10.138700MHz, get audio at 1500Hz and WSPR software will auto search and decode signal around 1500Hz?

  4. On my receiver, is it correct that audio will be 1200 and 2200Hz, when dialed to 10.138 or 10.139MHz? Will WSPR software auto search to 1200 and 2200Hz? If not, can I set it in the software? Or, I should vary BFO to make it "back to" 1500Hz?

  5. Are the below tabled calculation of LO and BFO, etc correct?

  6. The receiver only have setting of AM/SSB. It does not have separate setting for USB and LSB. It has a BFO knob with a 'central click" which got a good zero beat for 10MHz time signal.

To get effective USB mode, I believe I should turn it "away from the central click" in order to set BFO to 453.5KHz, right?

  1. If I turn the BFO knob to the "wrong" direction, setting BFO to 456.5KHz, resulting in LSB mode, I will hear similar signal tone, but, the 4 symbols are in "up side down frequency order" and cannot be decoded. Are these right?

enter image description here

  • $\begingroup$ Will the below bring the audio back_to_1500Hz and will work? For case 1 in table, changing BFO to 454.200KHz. For case 2, change to 453.200KHz. I live in city apartment and cannot receive HF. Need to figure it out as much as I could, before next country park hiking and bringing the receiver to hill area, like mini field day $\endgroup$ – EEd Jun 22 '16 at 20:15
  • $\begingroup$ You might try receiving inside your city apartment. WSPR is so very efficient that it may work fine in spite of the attenuation and the noise. Also, if you have a laptop computer you might consider trying to receive from a table in a park. Good luck! $\endgroup$ – rclocher3 Jun 27 '16 at 15:54

I'm neither an electrical engineer nor a software-defined radio expert, but I have used WSPR, so I'll have a go at answering your question.

You're correct that WSPR transmissions on 30m are centered around 10.1402 MHz, but the WSPR 2.0 User's Guide says that the passband is about 200 Hz wide since the software will generate tones between 1400 and 1600 Hz, and transceiver frequency drift can add to that. The screen shots in the User's Guide show a passband of slightly more than 200 Hz wide (see the scale at the right of the waterfall).

Most ham radio software for digital modes shows signals in the entire passband sent by the radio, typically 2.7 kHz wide or so, but K1JT's software decodes a much smaller passband, probably with the intention of keeping WSPR signals confined to a small part of the band since there is no need to use a larger passband.

I had a look at the manual for your Tecsun PL-600, which is quite vague about SSB reception. I think you're probably right about turning the BFO knob one way for USB and the other way for LSB. If I were in your situation I would test that theory by tuning the radio to the ham 20m band (14.225 to 14.350 MHz in the US), where USB is the norm, and also to the ham 40m band (7.175 to 7.300 MHz) where LSB is common. Tuning SSB signals in those two bands will tell you how the BFO knob works, and which way you twist for USB and which way for LSB.

I would suggest that you try W1JT's software before trying that Spectrum Lab software. If you can successfully decode signals with W1JT's software then you will know that your radio is tuned correctly, that the incoming signal voltage levels are correct, and so on.

Please keep in mind also that signals from the headphone jack of the radio are at about line level (~ 1 V), but the input level of the sound card in your computer may be at microphone level (millivolts). If that is the case, then an attenuator is necessary between the radio and the computer. Some sound cards have a line-level input, in which case an attenuator may not be necessary. For more details about such an attenuator, do a web search for "ham radio sound card interface". Sometimes galvanic isolation (a transformer) is required in the sound card interface in order to prevent ground loop problems.

Good luck, and let us know in a comment how things go!

  • $\begingroup$ First, WSPR software cannot decode. I could hear it with good SNR. Then I try to 'see' it on Spectrum Lab. If you kind enough to help, you may try a) dial RX to 10.138700 and should see signal in 1400 to 1600 using WSJT-X (experimental X software from same author, with wide spectrum display but only decode those at middle) b) dial to 10.139000, signal should 'move down 300Hz'. Ear will confirm that it was in down direction. Now, turn the RIT (BFO) knob, try either clockwise or anticlockwise, move tone UP by ear hearing.Waterfall will see it UP 300Hz, back to 1400 to 1600Hz and DECODE ok $\endgroup$ – EEd Jun 22 '16 at 20:41
  • $\begingroup$ These knob turning will be same as inside my receiver. I am in city apartment, cannot receive HF due to man-made noise. I can try on mini field day weekend by bringing stuffs to hill side. So, hope plan out and success next week. . Last week was not successful, see hear ok, decode bad. Must be some mis-setting my me. $\endgroup$ – EEd Jun 22 '16 at 20:45
  • $\begingroup$ Could you show us a screen shot of the software when you are unable to decode? $\endgroup$ – rclocher3 Jun 22 '16 at 20:49
  • $\begingroup$ Now cannot. Can do on next mini field day. Last time, I fixed the BFO at sightly anti clockwise beyond central click and vary deal frequency over about 6 steps of 1KHz each step. That was first trail without really thinking deeply into the EE theory of mixer. Hope, my today plan is 70% fine and same ham here can bring it to 100% before next outing test $\endgroup$ – EEd Jun 22 '16 at 21:00

30m WSPR signals can be anywhere inside the range 10,140,100 Hz to 10,140,295 Hz (which the software expects to see as an AF frequency of 1400 to 1595 Hz). The software simultaneously decodes at all frequencies inside that range looking for a valid signal, so that many transmitters can co-exist within the band — but it will ignore anything outside of that band (I think there is 20Hz or so of leeway).

So for reception you do want to tune your radio so that 10,140,200 Hz shows up right at 1500 Hz or else you will discard some valid on-air signal.


Compare with typical ham equipment, this SWL receiver, Tecsun PL-600

a) only tunes in 1KHz step

b) only has one SSB mode, without separate USB and LSB settings

Following is how to receive WSPR through adjustment of BFO to get 1500Hz audio.

The on air signal is 10.140200MHz + (0 to 3) x 1.4648Hz for 4 symbol frequencies.

  1. Set PL-600 dial frequency to 10.140MHz, SSB mode, Narrow Bandwidth, BFO first set to central click point then turned anti-clockwise 70 degrees.

  2. Adjust audio signal level for 0dB at WSPR, Dial 10.138700 Tx 10.140200

  3. Run WSPR 2.12, WSJT-X 1.6.0 and Spectrum Lab V2.90b16. Fine tuned BFO until audio signal was 1500Hz on water fall display.


Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.