I just built a homebrew antenna that consists of a full-length quarter-wave vertical sized for 20m, with a "top hat" consisting of a Hustler VP-1 and trio of Hustler mobile resonators (RM-80S, RM-40, and a RM-20 with extra-long whip repurposed to do 30m instead).

View of the antenna itself

The antenna works extremely well on 30 and 40 meters. It works as well as can be reasonably expected (for a ~22 foot tall antenna) on 80m. It works surprisingly well on 15m. It's absolutely dysfunctional on 20m.

More specifically, according to NanoVNA it's completely dysfunctional between approximately 14.04MHz and 14.16Mhz (the precise chunk of 20m I actually care about). It's like there's a bubble around that range of frequencies that adjusting the lower portion of the antenna simply can't fix.

Here's an example sweep from NanoVNA (ignore markers 0 and 1):

80 to 15 meter sweep

If I lengthen or shorten the lower element by up to a foot either way from ~17' (from ~18 feet to 16 feet), the pair of SWR valleys above and below 14.10Mhz shift left/right and slowly move towards each other... but right around 14.05 and 14.15Mhz, the minimum SWR value shoots up towards infinity as the two merge together somewhere far above the graphed range, leapfrog over the 100KHz chunk I care about, then come down and form a new pair of SWR curves flanking 14.10MHz. Eventually, if I keep lengthening or shortening the element, one of them has its SWR start to rise until it merges into the larger inter-band curve, and the other flattens out at a low SWR somewhere around 12 or 18Mhz.

Spoiler alert: the reason why I was using the RM-20 with a longer whip for 30m is because an earlier iteration of the antenna (built with a 5' lower shared mast) that tried using the RM-20 for 20 meters had the exact same problem... a SWR bubble centered around 14.10Mhz. What I failed to realize at the time was that even though I re-tuned it for 10.13Mhz by lengthening the whip, the same coil problem that screwed up its ability to work for 14.07Mhz was going to keep screwing up the ability of the antenna to work near that frequency.

  • $\begingroup$ The capacitance you mention should be very small. Have you measured the response on 20m after removing the resonators for the other bands? $\endgroup$
    – Brian K1LI
    Commented Mar 25, 2021 at 18:37
  • $\begingroup$ What radials do you have? How many, what length(s)? It sounds like it could be something about them, rather than the vertical radiator. Nothing wrong with your feed system, as long as you tune the radiator length. And how close by are those horizontal wires? $\endgroup$
    – tomnexus
    Commented Mar 25, 2021 at 21:34
  • $\begingroup$ @tomnexus Excellent point. And, for diagnostic purposes, I recommend evaluating the antenna on each band with just that band's "resonator" installed. $\endgroup$
    – Brian K1LI
    Commented Mar 25, 2021 at 23:56
  • $\begingroup$ @tomnexus, the power lines in the background are about twice as far away from the antenna's highest point as the antenna's highest point is from the ground. They run in a 10' utility easement behind the back yard, and the rear property line is about 40 feet away from the base of the antenna. The antenna itself is about 23 feet from ground to the tip of its longest resonator whip. $\endgroup$
    – Bitbang3r
    Commented Mar 26, 2021 at 1:08
  • $\begingroup$ @Brian, when I remove the resonators and VP-1 bracket, the weird bubble around 14.05 to 14.15 goes away, but my best-achievable SWR is still pretty disappointing... 1.67:1 at 14.07MHz, and 1.66:1 to 2.01:1 across the entire band. Tomorrow, I'll try sweeping all 8 permutations of the three resonators (none, one at a time, two at a time, all three) to try and figure out whether one in particular is screwing everything up. $\endgroup$
    – Bitbang3r
    Commented Mar 26, 2021 at 1:19

1 Answer 1


OK, it turns out, the Hustler RM-20 resonator was the culprit, after all. I removed it from the VP-1 mount (leaving only the RM-80S and RM-40), and the problem completely went away.

NanoVNA sweep with RM-20 removed:

NanoVNA sweep with RM-20 resonator removed

I did more research this morning, and learned that apparently, the RM-20's inability to work on the lower 20 meter band (where digimodes like FT8 live) is well known. Apparently, its designer pulled some optimization tricks that make it work better than expected (wider bandwidth, flatter and lower SWR curve) on the upper (SSB phone) portion of the 20m band, at the cost of rendering it completely unfit for use within a small chunk of the lower 20m band (which, unfortunately, is almost precisely centered on the chunk of frequencies used for 20m FT8).

The work-around is to buy a Hustler RM-17 instead, and pair it with a longer 3/32" diameter whip.

  • 1
    $\begingroup$ Good work, detective!! And, thanks for following up with this valuable information. $\endgroup$
    – Brian K1LI
    Commented Mar 26, 2021 at 19:05

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .