5
$\begingroup$

A quartz crystal is often represented by this equivalent schematic:

schematic

simulate this circuit – Schematic created using CircuitLab

How to measure quartz crystal motional parameters using a VNA? discusses measuring these parameters with a VNA, and there the most mathematically complex step is determining $C_p$. Is it feasible to measure $C_p$ directly with an LCR meter?

$\endgroup$
4
$\begingroup$

The impedance of $C_p$ is

$$ Z_p(\omega) = {1 \over i \omega C_p } $$

and the impedance of the other branch is

$$ Z_s(\omega) = R + i \omega L + {1 \over i \omega C_s} $$

and the impedance of the entire crystal is the parallel combination of these:

$$ Z_x(\omega) = \left( {1\over Z_p(\omega)} + {1\over Z_s(\omega)} \right)^{-1} $$

Typical values for an approximately 14 MHz crystal are:

$$\begin{align} R &= 7.37 \:\Omega\\ C_s &= 18.8\:\mathrm{fF}\\ C_p &= 4.15\:\mathrm{pF}\\ L &= 6.57\:\mathrm{mH} \end{align}$$

At 1.4 MHz:

$$ \begin{align} Z_p(2\pi 1400000) &= 0-27393i\\ Z_s(2\pi 1400000) &= 7.37 - 5989128i\\ Z_x(2\pi 1400000) &= 0.000152779-27269i \end{align}$$

An LCR meter is probably just measuring the magnitude of the voltage when applying a known AC current, so it will be off by a factor of:

$$ {|Z_x(2\pi 1400000)| \over |Z_p(2\pi 1400000)|} = 0.995447 $$

So for this particular crystal, measuring the impedance with an LCR meter (assuming no other inaccuracy in the device) at approximately 1/10th the serial resonance frequency of the crystal yields an error of less than 1%.

So, given an LCR meter that can be accurate with a reactance on the order of 30kΩ, this is not a bad way to go.

| improve this answer | |
$\endgroup$
2
$\begingroup$

Short answer: measure $C_p$ at a frequency far from any one of the crystal's resonant frequencies.
Be aware that not only is a crystal resonant on harmonics of its primary (printed) frequency, but spurious resonances also appear.

It is probably safest to measure the parallel-plate capacitance below resonant frequency. So yes, LCR bridges often use a signal source at low frequency. Since $C_p$ may be in the single-digit picofarad range, care should be taken to reduce stray capacitance of the measurement fixture.
You might measure $C_p$ with the crystal mounted in the LCR meter, then carefully remove the crystal without disturbing the environment, and measure stray capacitance. The true(er) $C_p$ is the difference between the two measurements.

For quartz AT-cut crystals, $C_p$ is very roughly 250 times larger than $C_s$.
You're unlikely to measure $C_p$ so accurately in a LCR meter or bridge that this factor need be considered.


Ceramic resonators are not as piezo-active as quartz, so the disturbing effect of $C_s$ requires factoring-in its effect on a $C_p$ measurement.
For example, an ultrasonic transducer was measured where $C_p$ was only 7.5 times larger than $C_s$.
Quartz has amazing qualities: very piezo-active, temperature-stable. Most other materials that are piezo-active pale in comparison.

| improve this answer | |
$\endgroup$

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.